Protecting The Environment; Technical Data; Troubleshooting - Stanley FATMAX KFMCD628 Manual De Instrucciones

ENGLISH
Keep the motor running while pulling the bit out of a drilled
u
hole. This will help reduce jamming.
Make sure switch turns drill on and off.
u
Drilling in wood
Holes in wood can be made with the same twist drill bits used
for metal or with spade bits.
These bits should be sharp and should be pulled out fre-
quently when drilling to clear chips from the flutes.
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulphurized cutting oil.
Drilling in masonry
Shift drill into 'Hammer mode'. Use carbide tipped masonry
bits. Refer to drolling section. Keep even force on the drill but
not so much that crack the brittle material. A smooth, even
flow of dust indicates the proper drilling rate.
LED work light
When drill is activated by pulling the trigger switch (1), the
integrated LED work light (8)will automatically illuminate the
work area.
Note: The work light is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Bit tip storage
A bit storage slot (9) is built into the base of the tool.

Troubleshooting

Problem Possible cause
Unit will not start. Battery pack not
installed properly.
Battery pack not
charged.
Unit starts immedi- The switch has
ately upon inserting been left in the "on"
battery position.
Battery pack will not Battery pack not
charge. inserted into charger.
Charger not plugged
in.
Surrounding air
temperature too hot or
too cold.
Unit shuts off Battery pack has
abruptly. reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
8
(Original instructions)
Possible solution
Check battery pack
installation.
Check battery pack charg-
ing requirements
The switch must be
moved to "off" to prevent
the tool from immediately
starting when battery is
inserted.
Insert battery pack into
charger until LED lights.
Plug charger into a work-
ing outlet.
Move charger and battery
pack to a surrounding air
temperature of above 45ºC
or below +40.5ºC
Allow battery pack to cool
down.
Place on charger
and allow to charge.
Maintenance
Your Stanley Fat Max tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
u
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior.

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries accord-
ing to local provisions. Further information is available at
www.2helpU.com.

Technical data

Voltage
No-load speed
Max. torque
Chuck capacity
Max Drilling capacity
Masonry/Steel/wood
Weight
Charger
Input voltage V
AC
Output voltage
V
DC
Current mA
Approx. charge time Mins
Battery FMC685L
Voltage
V 18
AC
Capacity Ah 1.5
Type
Li-Ion
KFMCD628 (H1)
V
DC
Min 0-430/0-1700
-1
Nm
mm
mm
kg
905998** 906086** 906364**
230 230
18 18
1000 2000
80-240 40-120
FMC687L FMC688L FMC684L
18 18
2.0 4.0
Li-Ion Li-Ion
18V
55
13
13/13/35
1.5
230
20
1000
80-240
18
1.3
Li-Ion