Safety Alert Symbol; Important Safety Instructions; Prior To Installation - BriskHeat TSREH Manual De Instrucciones

TSREH Silicone Rubber Enclosure Heaters

IMPORTANT SAFETY INSTRUCTIONS

SAFETY ALERT SYMBOL

The symbol above is used to call your attention to instructions
concerning your personal safety. It points out important safety
precautions. It means "ATTENTION! Become Alert! Your
Personal Safety is involved!" Read the message that follows
and be alert to the possibility of personal injury or death.
A person who has not read and understood all operating
instructions is not qualified to operate this product.

Do not immerse or spray any component of the
control system with liquid.

Keep volatile or combustible material away from
control and heating system when in use.

Keep sharp metal objects away from control and
heating system.

Use control and heating system only in approved
locations.
Failure to observe these warnings may result in electric
shock, risk of fire, and personal injury.
WARNING
End User Must Comply to the Following:

Only qualified personnel are allowed to connect
electrical wiring

All electrical wiring must follow local electrical codes
and NEC Article 427

The person who performs the final installation / wiring
must be qualified for this work.

The end-user is responsible for providing a suitable
disconnect device

The end-user is responsible for providing a suitable
over-current protection device. It is highly
recommended that a ground-fault circuit breaker be
used
Failure to observe these warnings may result in personal
injury or damage to the heater.
®
© BriskHeat Corporation. All rights reserved
DANGER
Immediate hazards which WILL result in severe personal injury
or death.
WARNING
Hazards or unsafe practices that COULD result in severe
personal injury or death.
CAUTION
Hazards or unsafe practices that COULD result in minor personal
injury or property damage.

Inspect all components before use.

Never handle the heater while it is in operation;
always disconnect the heater from the power source
and allow cooling prior to handling.

Designed for use of metal surfaces. Do not use on
plastic surfaces.

If spillage of foreign matter onto heater occurs,
disconnect from power source and clean after heater
is allowed to cool.

Never operate a heater without an appropriate heat
sink (device being heated is considered a heat sink).

Do not operate heater above rated temperature value.

Fasten heater to device using approved methods
only.

Do not use control and heating system if any
component is damaged.

Do not repair damaged or faulty control and heating
systems.

Do not crush or apply severe physical stress on any
component of system, including cord assembly.

Unplug control and heating system when not in use.
Failure to observe these warnings may result in personal
injury or damage to the heater.
.
3
TSREH Silicone Rubber Enclosure Heaters
Read and understand this entire manual before operating this electric heater.

PRIOR TO INSTALLATION

1. Check for suspected damage to the heating blanket like rips, punctures, etc.
2. Confirm voltage / wattage rating of heater. The heater is designed to work at a specific
voltage to heat properly. For additional information, contact your local distributor or
®
BriskHeat .
3. Confirm blanket maximum exposure temperature rating is suitable for environment.
The temperature of the internal heating element may run up to 25% higher than the
external surface of the blanket. Use extreme caution for applications that require a
process temperature near the maximum exposure temperature ratings of the blanket.

Silicone rubber heating blanket exposure temperature range:
-70ºF to 392ºF (-57ºC to 200ºC)
MOUNTING YOUR HEATER ONTO THE ENCLOSURE SURFACE:
Your silicone enclosure heater is pre-attached to an aluminum mounting plate. The
mounting plate has two 0.156" (4 mm) x 0.250 (6mm) oval shaped mounting holes pre cut
into a 0.5" (13mm) flange (A).
Mounting Holes (B) are centered on the flange 4" apart for the 6" heater and 9" apart for the
12" heater.
Drawing:
Prior to mounting your heater:
1. Find a location within the enclosure where there is sufficient clearance between the
heater and other components.
2. Determine whether vertical or horizontal mounting is preferable in the location chosen.
3. If the heater has a built-in thermostat and is to be mounted vertically, then thermostat
should be located at the lower end.
4. Use the holes provided to mount the heater onto a sub-panel or to other available
mounting surface.
®
© BriskHeat Corporation. All rights reserved
.
4