Autoselect - Black and Decker FSMH1300FX Traducido De Las Instrucciones Originales

ENGLISH
Removing a cleaning pad
Caution! Always wear suitable shoes when changing the
cleaning pad on your steam mop.
Do not wear slippers or open toed footwear.
Return the steam mop to the upright position and turn the
u
steam mop 'OFF'.
Wait until the steam mop cools down (approximately 5
u
minutes).
Lift the steam mop away from the cleaning pad freeing it
u
from the velcro fastening by putting weight on the cleaning
pad removal tab (11).
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop supported in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Filling the water tank (Fig. D)
Note! Fill the water tank with clean tap water (Do not use any
additives or chemicals).
Note! In areas of hard water, the use of de-ionised water is
recommended.
Open the filler cap (4) by flipping it up.
u
Fill the water tank with water (Do not use any additives or
u
chemicals).
Warning! When filling, maintain in a horizontal position.
Warning! Your water tank has a 0.5 litre capacity. Do not over
fill the tank.
Close the filler cap (4).
u
Note! Ensure the filler cap is firmly secured.
Use
Important! This unit will kill 99.9% of bacteria and germs
when used in accordance with the instructions in this manual
and with the micro fibre pads fitted and a continuous run time
of 90 seconds.
Switching on and off (Fig. F)
To switch the appliance on, press the ON/Off switch (1).
u
It takes approximately 20 seconds for the steam mop to
heat up.
To switch the appliance off, press the ON/Off switch (1).
u
Caution! Never leave the steam mop in one spot on any
surface for any period of time.
Always place the steam mop supported in the upright position
when stationary and make sure the steam mop is turned off
when not in use.
Caution! Always empty the steam mop after use.
Note! When first filled or after running dry, it can take up to 45
seconds for steam to be produced.
10
(Original instructions)

Autoselect

Technology (Fig. E)
TM
This steam mop is fitted with an Autoselect
shows various cleaning applications. They are used to select
the correct operating mode for your particular cleaning
operation.
Using Autoselect , choose from one of the following
TM
applications by turning the Autoselect
required setting is selected.
Setting Mop
Wood/Laminate
Tiles/Vinyl
Stone/Marble
The steam mop will select the correct volume of steam
required for your particular cleaning operation.
Note: Always check you are using the correct setting before
using your steam mop.
Attaching the hose and accessories to the
hand held steam cleaner
Warning! Inspect the seal between the connection point on
the hand held steam cleaner and the steam hose (12) before
each use. If the seal malfunctions or is damaged, please
contact your nearest authorised repair agent. Do not use the
appliance.
Attaching the hose (Fig. H)
Press the steam hose release button (17) on the steam
u
hose (12).
Connect the steam hose (12) to the hand held steam
u
cleaner and release the steam hose release button (17)
making sure it clicks into place.
Important! Ensure that the steam hose (12) is securely
connected to the hand held steam cleaner. If steam escapes
from the joint, the hose is incorrectly fitted. Switch off, allow
the unit to cool then remove and refit the hose.
Warning! The unit should be switched off before the hose is
fitted.
Attaching accessories (Fig I)
Align the lugs on the steam nozzle (12) with the recesses
u
on the accessory.
Press the accessory onto the steam nozzle and twist
u
anticlockwise until the accessory clicks into place.
Important! All accessories must be attached to the steam
hose (12) for use.
Removing the hose and accessories
Warning! The steam hose (12), Steam nozzle and
accessories become hot during use.
dial (2) which
TM
dial (2) until the
TM
Hand held
Low steam flow

Medium steam flow
 
High steam flow
  