MAG TOOLS MPF980381 Manual De Instrucciones página 6

• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of
electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI)
protected supply. Use of a GFCI reduces the risk of electric shock.
• Recharge only with the charger specifi ed by the manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fi re when used with another battery pack.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally
occurs, fl ush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
4) ADDITIONAL SPECIFIC SAFETY RULES FOR IMPACT WRENCHES
• Use only impact rated accessory sockets and extensions recommended by Mac Tools. Inspect accessories
before use. Do not use cracked or damaged accessories. Do not use chrome sockets , hand sockets or any
other accessories not rated for impact use.
• The tool's power is controlled by the pressure exerted on the trigger, fi rmly grip the tool and squeeze the
trigger to operate.
• Do not use sockets with excessive wear to the input or output drives. Periodically check the square drive
on the impact wrench. Make sure the socket, extension bar, or other attachment is securely fi tted before
operating tool.
• When loosening fasteners fi rst ensure that there is suffi cient clearance behind the tool to avoid hand
entrapment. The tool will move away from the threaded joint as the nut/bolt is loosened and rides up the
thread, moving the tool with it. Make sure hands are kept away from the sockets during tool use.
• Securely fi t the socket or attachment to the impact wrench. Inspect anvil and retaining ring of tool prior to
use. Missing or damaged items should be replaced before use.
• Ensure that the forward/reverse switch is in the correct position for tightening or loosening the fastener.
• The nut/bolt can then run down the thread using the power drive of the tool. For loosening a joint the tool
can be used in the reverse sequence.
• Recommended to use a hardened steel (or material with comparable shock resistance) threaded hose
fi tting (Fig 6).
5) POWER TOOL USE AND CARE
• Before running the tool, check that there is no dangerous interaction with the immediate environment
(explosive gas, fl ammable or dangerous liquid, unknown piping, electric sheathing or cable, etc).
• Before connecting the tool to the air inlet, check the trigger is not blocked in the on position by an obstacle.
• In the event of blockage, release the trigger and disconnect the tool from the compressed air network.
• Ensure that the unit on which work is being carried out is immobilized.
• Always operate, inspect and maintain this tool in accordance with all regulations (local, state, federal and
country), that may apply to hand held/hand operated pneumatic tool.
• For safety, top performance, and maximum durability of parts, operate this tool at 90 psig.
(6.2 bar / 620 kPa) maximum air pressure at the inlet with 3/8'' (10mm) inside diameter air supply hose.
• Always use clean, dry air. Dust, corrosive fumes and/or excessive moisture can ruin the motor of an air tool.
• Exceeding the maximum pressure of 90 psig (6.2 bar / 620 kPa) will lead to the risk of danger such as
excessive speed, tool wear, breaking parts, higher torque or force that may destroy the tool and its accesso-
ries or the part being worked on.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other
condition that may affect the power tool's operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
• Use rated accessories recommended by Mac Tools only. Inspect accessories before use. Do not use crac-
ked or damaged accessories. Just because the accessory can be attached to your power tool, it does not
assure safe operation.
• Use the power tool, accessories and tool bits, etc. in accordance with these instructions, taking into ac-
count the working conditions and the work to be performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
6
MACTOOLS.COM