General Information; Start-Up And Operation; Preventive Maintenance - 3M Scotch-Weld LT Manual Del Propietário

Aplicador por fusión al calor
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

ENGLISH

General Information

Thumb pressure on the feeder pushes the adhesive stick into
the heat block. The adhesive is melted by the heat block and
pushed out through the tip. A fixed thermostat on the heat
block maintains heat block temperature.

Start-Up and Operation

WARNING: USE ONLY 3M™ SCOTCH-WELD™ HOT MELT
2'' x 5/8'' LOW MELT ADHESIVE STICKS. OTHER
ADHESIVES MAY CAUSE BACKMELT AND POSSIBLE
INJURY. DO NOT USE NEAR HIGHLY FLAMMABLE
MATERIALS.
1. Plug the 3M™ Scotch-Weld™ Hot Melt Applicator LT into
a 120 VAC grounded receptacle. Allow 5 to 10 minutes for
heat-up.
2. Pull the feeder back toward the rear of the applicator.
3. Snap a 3M Scotch-Weld Hot Melt Adhesive Stick
(5/8'' x 2'') into the holder.
CAUTION: Do not force adhesive. Excessive force
can damage the applicator and cause molten
adhesive to flow out the rear.
4. Gently press the feeder forward and push the adhesive
into the heat block. Melted adhesive will flow from the tip.
WARNING: TIP AND VALVE ARE HOT. KEEP TIP POINTED
AWAY FROM BODY PARTS.
CAUTION: To avoid charring or plugging of the tip,
extrude at least one adhesive stick every three hours that
the applicator is turned on.
Shut-Down
1. Unplug the applicator.
2. Extrude one adhesive stick to cool down the applicator.

Preventive Maintenance

WARNING: TIP AND VALVE ARE HOT. WEAR HEAT-
RESISTANT GLOVES WHEN CLEANING TIP. KEEP TIP
POINTED AWAY FROM BODY PARTS.
To maintain proper operation, follow these steps.
1. Inspect nozzle tip daily. Make sure it is clean and clear of
foreign matter.
2. Keep the adhesive clean and free of airborne
contaminants.
Accessory Tips
The 3M Scotch-Weld Hot Melt Applicator LT comes equipped
with a standard .093'' tip. Contact your 3M Scotch-Weld Hot
Melt Applicator distributor for additional tips.
Applicator must be at operating temperature. Hold the valve
firmly with a 5/8'' wrench and remove the tip with a 1/2''
wrench. Mount the new tip and tighten.
Tip
Description
9725
Mini-extension/0.072'' opening
9726
"T" tip/RSC carton closing
9727
"L" tip/FOL carton closing
9785
.070" Tapered aluminum extension
9940
.125'' opening
9913
Two-hole spreader
9916
Three-hole spreader
9921
Standard .093'' opening
9922
.063'' Fluted tip
Changing Tips
WARNING: THE TIP AND VALVE ARE HOT. WEAR HEAT-
RESISTANT GLOVES AND POINT TIP AWAY FROM BODY
PARTS.
CAUTION: Do not overtighten. Overtightening damages
threads.
Repair Parts Kit
9234 Valve Assembly Kit
a. .093'' tip
b. Valve Assembly
9237 Sleeve Kit
a. Sleeve
b. Brass Flange (4)
9238 Feeder Kit
a. Feeder
b. Metal Clip
9284 Power Cord Kit
a. Power Cord (orange)
9262 Heater/Thermostat Kit
a. Heater Assembly
b. Thermostat/TCO
3M Stock # 62-9234-9930-5
3M Stock # 62-9237-9930-8
3M Stock # 62-9238-9930-6
3M Stock # 62-9284-9930-0
3M Stock # 62-9262-9930-6

Publicidad

Tabla de contenido
loading

Tabla de contenido