Shark 10006669 Manual Del Usuario página 2

day. If it is necessary to set the date dur-
ing that time period, first change the time
to any time outside it, then set the date
and then reset to the correct time.
TO USE THE CHRONOGRAPH (STOP-
WATCH):
1. Press S1 button to start counting.
2. To stop counting, press S1 button once.
Press S1 button again to resume from
where it left off.
3. To reset to zero, press S1 button to
stop counting and then press S2 button.
A B C
1. Hour Hand
2. Minute Hand
3. Second Hand
4. 24 Hour Hand
5. Chronograph Minute Hand
6. Chronograph Second Hand
7. Calendar
S1 – Chronograph start/stop button
S2 – Chronograph split/split release/
reset button
TO ADJUST THE CHRONOGRAPH HANDS
POSITION:
Before setting the time, check if the
Chronograph Second Hand and Chrono-
graph Minute Hand are at the 12 o'clock
position.
If the chronograph is in use, press the
button in the following order to reset it,
and then check if the chronograph hands
have returned to 12 o'clock position.
If the chronograph is counting: S1 S2
If the chronograph is stopped: S2
If the split time is displayed:
In case one or several chronograph hands
are not at the 12 o'clock position due to
certain reasons (e.g. following a battery
change), that needs to be adjusted.
1. Pull crown out to second click
position C.
2. Press S1 or S2 button to set the
Chronograph Second Hand and
Chronograph Minute Hand (me
chanically coupled). By pressing S1 or
S2 button, the hands will move
counter-clockwise or clockwise
respectively.
3. Push crown back to position A.
TO SET THE TIME:
1. Pull crown out to second click position
C.
2. Turn crown to set time.
3. Push crown back to position A.
NOTE: The 24 Hour Hand will also be set
during time setting.
TO SET THE DATE:
1. Pull crown out to first click position B.
2. Turn crown clockwise to set date.
3. Push crown back to position A.
NOTE: Do not set the date between 9:00
P.M. and 1:00 A.M. Otherwise, the date
may not change properly on the following
day. If it is necessary to set the date dur-
ing that time period, first change the time
to any time outside it, then set the date
and then reset to the correct time.
TO USE THE CHRONOGRAPH (STOP-
WATCH):
For the measurement of elapsed time,
1. Press S1 button to start counting.
2. To stop counting, press S1 button once.
Press S1 button again to resume from
where it left off.
3. To reset to zero, press S1 button to stop
counting and then press S2 button.
For the measurement of split time,
1. Press S1 button to start counting.
2. While the chronograph is running,
press S2 button once to register a lap.
The chronograph is still running in the
background.
To display the currently accumulated
time, press S2 button again. The chro-
nograph hands will quickly advance to
the ongoing measured time.
3. Repeat the last step until all the laps
have been registered.
4. To reset to zero, press S1 button to stop
counting and then press S2 button.
NOTE: The chronograph is able to mea-
sure up to 60 minutes.
1. Hour Hand
2. Minute Hand
3. Second Hand
4. 24 hour Hand
5. Chronograph Second Hand
6. Chronograph Minute Hand
S1 – Chronograph start/stop button
S2 – Chronograph reset button
TO ADJUST THE CHRONOGRAPH HANDS
POSITION:
Before setting the time, check if the Chro-
nograph Second Hand and Chronograph
Minute Hand are at the zero position.
S2 S1 S2
If the chronograph is in use, press the
button in the following order to reset it,
and then check if the chronograph hands
have returned to zero position.
If the chronograph is counting: S1 S2
If the chronograph is stopped: S2
In case one or several chronograph hands
are not at the zero position due to certain
reasons (e.g. following a battery change),
that needs to be adjusted.
1. Pull crown out to first click position B.
2. Press S1 button to set the Chronograph
Second Hand and Chronograph Minute
Hand (mechanically coupled). Hold-
ing down the button will allow quick
advance.
3. Push crown back to position A.
TO SET THE TIME:
1. Pull crown out to first click position B.
2. Turn crown to set time.
3. Push crown back to position A.
NOTE : The 24 Hour Hand will also be set
during time setting.
TO USE THE CHRONOGRAPH (STOP-
WATCH):
For the measurement of elapsed time.
1. Press S1 button to start counting.
2. To stop counting, press S1 button once.
Press S1 button again to resume from
where it left off.
3. To reset to zero, press S1 button to stop
counting and then press S2 button.
NOTE : The chronograph is able to
measure and display time in 1 second unit
up to maximum of 29 minutes 59 seconds.
The chronograph will stop automatically
after running continuously for 30 minutes.
TO USE THE BACKLIGHT:
Some watch models are equipped with an
electroluminescence (EL) backlight. To
turn on the backlight, press the backlight
button.
If there is no separate backlight button,
press the crown to activate the backlight.
SCREW-DOWN CROWN:
Some watch models are equipped with
a screw-down crown. Make sure to un-
screw the crown before pulling out the
crown for setting, then screw the crown
back in tightly after setting to avoid any
water entry.
TO USE THE COMPASS
A B
JS50
The red pointer of the compass repre-
sents the direction of magnetic North (N).
With reference to the red pointer, you can
then locate the directions of East, South
and West.
DISCLAIMER - The compass should not
be relied upon to determine precise loca-
tion, proximity, distance or direction. In
addition, some areas have more magnetic
interference than others. This interfer-
ence may result in further distortion of
the compass reading. This compass is
designed to point to magnetic north, not
true north. Please take into consideration
the level of declination based on your
global position.
To reduce carbon foot print, these
SHARK instructions are printed with
ENGLISH
N
W
E
S
soy inks on recycled paper.