General Information; Unpacking; Accessory Box; Assembly - Generac GP Serie El Manual Del Propietario

General Information

1.1 UNPACKING

• Remove all packaging material.
• Remove separate accessory box.
• Remove the generator from carton.

1.1.1 ACCESSORY BOX

Check all contents. If any parts are missing or damaged locate an
authorized dealer at 1-888-436-3722.
Contents Include:
• 1 – Owner's Manual
• 1 - Quart Oil SAE 30
• 2 - Never-Flat Wheels
• 1 - Hardware Bag (containing the following):
2 - Rubber Bumpers
2 - 5/16" Flat Washers
4 - 5/16" Carriage Bolts
2 - 1/2" Axle Pins
2 - 1/2" Flat Washers

1.2 ASSEMBLY

The generator requires some assembly prior to use.

If problems arise when assembling the generator, please call
the Generator Helpline at 1-888-436-3722.

1.2.1 ASSEMBLING THE ACCESSORY KIT

The wheels are designed into the unit to greatly improve the
portability of the generator.
The wheels are not intended for over-the-road use.
1. Refer to Figure 1 and install Wheels as follows:
• Slide the 1/2" Axle Pin through the 1/2" Flat Washer, Wheel
and Wheel bracket on frame.
• Install the Cotter Pin through the hole in the axle pin, then
bend the cotter pin prongs outward to secure wheel to
frame.
2. Refer to Figure 1 and install Frame Foot and Rubber Bumpers
as shown.
• Slide Rubber Bumper Stud through Frame Foot, then install
5/16" Locking Flange Nuts.
• Slide Frame Foot onto 5/16" Bolts, then install 5/16" Locking
Flange Nuts.
3. Refer to Figure 2 and install Handles as shown.
• Remove top Curved Head Bolts and Cap Nuts (Cap Nuts will
be re-used).
• Slide Handle Assembly over Frame Tube, aligning 2 holes.
• Slide 5/16" Carriage Bolts through; Install 5/16" Cap Nuts.
4
• 1 - Left Handle Assembly
• 1 - Right Handle Assembly
• 1 - Frame Foot
2 - 5/16" Bolts
4 - 5/16" Locking Flange
Nuts
2 - 5/16" Locking Cap Nuts
2 - Cotter Pins
NOTE:
Figure 1 – Wheel Assembly
2X COTTER PIN
2X 1/2" FLAT WASHER
2X WHEEL
2X 1/2" AXLE PIN
FOOT
2X RUBBER BUMPER
Figure 2 – Install Handle Kit

2.1 KNOW THE GENERATOR

Read the Owner's Manual and Safety Rules before operating
this generator.
Compare the generator to Figures 3 through 6 to become
familiarized with the locations of various controls and adjustments.
Save this manual for future reference.
1. 120 Volt AC, 20 Amp, GFCI Duplex Receptacle – Supplies
electrical power for the operation of 120 Volt AC, 20 Amp,
single-phase, 60 Hz electrical lighting, appliance, tool and
motor loads.
2. 120/240 Volt AC, 30 Amp Locking Receptacle – Supplies
electrical power for the operation of 120 and/or 240 Volt AC,
30 Amp, single-phase, 60 Hz, electrical lighting, appliance,
tool and motor loads.
3. Circuit Breakers (AC) – Each receptacle is provided with
a circuit breaker to protect the generator against electrical
overload.
4. Hourmeter – Tracks hours of operation.
5. Air Filter – Filters intake air as it is drawn into the engine.
6. Choke Knob – Used when starting a cold engine.
2X 5/16" BOLT
2X 5/16" FLAT WASHER
4X 5/16" LOCKING FLANGE NUT