Andis SBLC Instrucciones De Uso Y Cuidado página 6

CHANGING THE BLADE DRIVE ASSEMBLY
If your clipper blades no longer cut properly (be sure to try more than one blade, since the blade currently
being used may be dull), it could be that your blade drive assembly needs replacement.
TO CHANGE THE BLADE DRIVE ASSEMBLY:
1. Remove blade set (Figure M).
2. Remove drive cap by grabbing on both sides at top and sliding off (Figure R).
3. Remove blade drive mounting screws (Figure S).
4. NOTE: Before removing blade drive assembly, note the way it is positioned (this will help you in reassembly).
Remove blade drive assembly (Figure T).
5. Drive bearing should be at its lowest position (see Figure U for correct position of drive bearing), if not,
move it with your finger to lowest position (see Figure V for incorrect position of drive bearing).
6. Put on new drive assembly, align screw holes and press down (Figure T).
7. Reassemble blade drive by mounting screws (Figure S).
8. Replace drive cap by sliding back on clipper into position (Figure R).
9. Replace blade (Figure M).
USE GUIDELINES FOR LITHIUM-ION BATTERIES
1. The lithium-ion battery included with your clipper does not develop a "memory effect" like a nickel-metal
hydride (NiMH), or nickel cadmium (NiCd) battery. You can return the clipper to the charger at any time for a
full charge, or even use the battery before a charge cycle is complete. Like most rechargeable batteries,
lithium-ion batteries perform best when used frequently.
2. For maximum battery life, store the clipper in a partially discharged condition if the unit will be unused for
several months.
3. Avoid locating the clipper near heat vents, radiators, or in direct sunlight. Optimum charging will result
where the temperature is stable. Sudden increases in temperature can result in the battery receiving less
than a full charge.
4. Many factors influence lithium-ion battery life. A battery that has received heavy use or is more than a year
old may not give the same run-time performance as a new battery pack.
5. New lithium-ion batteries, unused for a period of time, may not accept a full charge. This is normal and
does not indicate a problem with the battery or charger. The battery will accept a full charge after several
cycles of clipper use and recharging.
6. Disconnect the charger or the clipper from the AC outlet if extended periods of non-use are anticipated.
CARE AND SERVICING OF THE ELECTRICAL SYSTEM
Your clipper and adapter cord are an integrated electrical system. Good electrical contact must be maintained
for the motor to deliver full power and lithium-ion battery to charge properly. Limited or erratic performance
caused by dirt or age can be corrected in the majority of cases.
BLADE & CLIPPER/TRIMMER REPAIR SERVICE
When the blades of your Andis clipper/trimmer become dull after repeated use, it is advised to purchase a
new set of blades available through your Andis supplier. Some blade sets can be resharpened - contact your
Andis supplier or the Andis Company for information on resharpening. If you wish your clipper/trimmer to be
serviced as well, contact your Andis supplier. If you have a problem contacting your Andis supplier contact the
Andis Company customer service department 1-262-884-2600 (USA) or email at info@andisco.com. To find an
Andis authorized service station, contact the Andis Company Customer Support Team at 1-262-884-2600,
or by email at support@andisco.com.
PROPER BATTERY DISPOSAL
The product you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its
useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal
waste stream. Check with your local solid waste officials for details in your area for recycling options or proper
disposal.
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed with other household wastes
throughout the EU. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the retailer where the
product was purchased. They can take this product for environmental safe recycling.
CAUTION: Never handle your Andis clipper while you are operating a water faucet and never hold your
clipper under a water faucet or in water. There is danger of electrical shock and damage to your clipper.
ANDIS COMPANY will not be responsible in case of injury due to this carelessness.
6