User Maintenance - Andis SBLC Instrucciones De Uso Y Cuidado

CORDED OPERATION
If the clipper powers OFF in the middle of a clipping job, the adapter cord can be attached to continue use in
corded operation. When the clipper is running with the adapter cord attached, the green light will remain ON.
The clipper will not charge while in use with the cord attached. After using your Andis clipper, rewrap cord
loosely and store in a safe place.
To start clipper, move power switch to ON position. To stop clipper, move power switch back to original
position (Figure K).
2-SPEED OPERATION
Your Andis clipper is equipped with two cutting speeds. The speeds are adjusted using the switch on the top
of the unit (Figure K). Setting "O" indicates the off position, Setting "1" is low speed and Setting "2" is high
speed. After using your Andis clipper, rewrap cord and store in a safe place.
CHARGING INDICATOR LIGHT
When the clipper is running, a green charging indicator light means the battery has a strong charge (Figure J).
When the light turns red, the battery may not hold enough charge to complete a large clipping job, and
should be recharged as soon as possible. If the clipper powers OFF, move the power switch to the OFF position
and plug the adapter cord directly in the receptacle on the bottom of the clipper (Figure H).
Automatically powering off protects the lithium-ion battery and is not a malfunction. The clipper will resume
normal operation when it is recharged.

USER MAINTENANCE

Cleaning and user maintenance shall not be made by children without
supervision.
The internal mechanism of your clipper has been permanently lubricated at the factory. Other than the
recommended maintenance described in this manual, no other maintenance should be performed, except by
Andis Company or an Andis authorized service station.
REMOVING BLADE SET
To remove blade set, first make sure your clipper motor is switched off, then push down on blade with one or
both thumbs (Figure L) and slide blade off blade hinge (Figure M). Some models are equipped with a blade
locking mechanism. To remove the blade, press down on blade locking mechanism while pushing blade off of
clipper. If your blade hinge should snap closed and is flush with the clipper, use a small standard screw driver
to pry the tongue of the hinge out (Figure N). NOTE: Hair may accumu late in the front cavity of the housing
under the blade. If this hap pens, you can clean out the hair by brushing out the cavity with a small brush or
an old toothbrush while the blade is off the clipper.
REPLACING OR CHANGING BLADE SET
To replace or change your blade set, slide the blade bracket onto the hinge of the clipper (Figure M), and with
the clipper turned "ON", push the blade towards the clipper to lock into position.
BLADE TEMPERATURE
Due to the high speed nature of Andis clippers, please check for blade heat often, especially on close cutting
blades. If blades are too hot, dip the blades only into Andis Blade Care Plus or apply Andis Cool Care Plus and
then Andis Clipper Oil. If you have a detachable blade unit, you can change your blade in order to maintain a
comfortable temperature; using multiple blades of the same size is popular among professionals.
CARE AND SERVICING OF YOUR ANDIS CLIPPER BLADES
Blades should be oiled before, during, and after each use. If your clipper blades leave streaks or slow down,
it's a sure sign blades need oil. The clipper should be held in the position shown in Figure O to prevent oil
from getting into the motor. Place a few drops of Andis Clipper Oil on the front and side of the cutter blades
(Figure P). Wipe excess oil off blades with a soft dry cloth. Spray lubricants contain insufficient oil for good
lubrication, but are an excellent clipper blade coolant. Always replace broken or nicked blades to prevent
injury. You can clean the excess hair from your blades by using a small brush or worn out toothbrush. To clean
the blades we suggest to immerse the blades only into a shallow pan of Andis Blade Care Plus, while the
clipper is running. Any excess hair and dirt that has accumulated between the blades should come out. After
cleaning, turn your clipper off and dry blades with a dry cloth and start clipping again.
If upon cleaning your blades you find that the blades will still not cut, there may be a few fine pieces of hair
trapped between the upper and lower blade. If this happens, you will need to snap the blade off the clipper.
Proceed to slide the upper blade to one side, without loosening the tension spring or moving the upper blade
completely out from under the tension spring (see Figure Q for position of blade). Wipe the surface between
the blades clean with a dry cloth, then place a drop of clipper oil where the upper and lower blades meet and
also in the guide slot of the tension spring (Figure Q). Now slide the upper blade to the opposite side of the
lower blade and repeat this process. After completing this procedure, slide the upper blade, centering it over
the lower blade. Handle or store your Andis clipper with the blades down so excess oil will not run into the
clipper case.
5