Ferroli ENERGY TOP B Instrucciones De Uso, Instalación Y Mantenimiento página 58

EN
• Carefully read and follow the instructions contained in this instruction booklet.
• After boiler installation, inform the user regarding its operation and give him this manual, which is an integral
and essential part of the product and must be kept with care for future reference.
• Installation and maintenance must be carried out by professionally qualified personnel, in compliance with
the current regulations and according to the manufacturer's instructions. Do not carry out any operation on
the sealed control parts.
• Incorrect installation or inadequate maintenance can result in damage or injury. The Manufacturer declines
any liability for damage due to errors in installation and use, or failure to follow the instructions.
• Before carrying out any cleaning or maintenance operation, disconnect the unit from the electrical power sup-
ply using the switch and/or the special cut-off devices.
• In case of a fault and/or poor operation, deactivate the unit and do not try to repair it or directly intervene.
Contact professionally qualified personnel. Any repair/replacement of the products must only be carried out
by qualified personnel using original replacement parts. Failure to comply with the above could affect the
safety of the unit.
• This unit must only be used for its intended purpose. Any other use is deemed improper and therefore haz-
ardous.
• The packing materials are potentially hazardous and must not be left within the reach of children.
• The unit must not be used by people (including children) with limited physical, sensory or mental abilities or
without experience and knowledge of it, unless instructed or supervised in its use by someone responsible
for their safety.
• The unit and its accessories must be appropriately disposed of, in compliance with the current regulations.
• The images given in this manual are a simplified representation of the product. In this representation there
may be slight and insignificant differences with respect to the product supplied.
Dear Customer,
Thank you for choosing
advanced design and cutting-edge technology. Please read this manual care-
fully since it provides important information on safe installation, use and maintenance.
is a high-efficiency modular premix condensing
low emissions , running on natural gas or LPG and arranged for in-
stallation in cascade.
Each module is equipped with one (version
or two (version
premix burners, housed in a vertical cabinet in epoxy powder coated steel resistant to
atmospheric agents.
The plumbing circuits of the exchangers, each equipped with its own local circulating
pump, run into system delivery and return manifolds inside the module. The control sys-
tem has a microprocessor, user interface with a large display and advanced cascade
control functions.
16 17 19
11
4
21
3
13
10
6 8 14
The control panel is located inside the cabinet. To access it, open the front door with the
special key supplied.
Key
DHW temperature setting decrease button (with optional hot water tank in-
stalled)
DHW temperature setting increase button (with optional hot water tank in-
stalled)
Heating system temperature setting decrease button
Heating system temperature setting increase button
Display
Summer/Winter mode selection button
Economy/Comfort mode selection (with optional hot water tank installed) and
unit On/Off button
Reset button
DHW operation (with optional hot water tank installed)
Summer mode
Multifunction
Eco (Economy) mode (with optional hot water tank installed)
Heating mode
All manuals and user guides at all-guides.com
, a latest-generation heat generator featuring
) aluminium finned tube exchangers with steel
18 20 23 5
eco
reset
comfort
24 7
cod. 3540S736 - Rev. 00 - 09/2013
Unit On / Off button
Burner On
Appears on connecting the Remote Timer Control (optional)
Information symbol
Top boiler shell
Top boiler shell system fault reset request
Fault
Circulating pump On
Appears on connecting the external probe (optional)
Boiler Off
Bottom boiler shell
Bottom boiler shell system fault reset request (model
only)
A heating demand (generated by the Room Thermostat or Remote Timer Control or 0-
10 Vdc signal) is indicated by activation of the circulating pump and the radiator (details
13 and 21 - fig. 1).
The display (detail 11 - fig. 1) shows the actual heating delivery temperature and, during
heating standby time, the message
fig. 1) indicates which boiler shell is on.
reset
A hot water tank heating demand is indicated by activation of the circulating pump and
the tap (details 9 and 21 - fig. 1). The display (detail 11 - fig. 1) shows the actual hot water
tank sensor temperature and, during heating standby time, the message
)
of the arrows (details 18 and 24 - fig. 1) indicates which boiler shell is on.
reset
Hot water tank temperature maintaining/heating can be excluded by the user. If exclud-
ed, domestic hot water will not be delivered. The hot water tank can be deactivated by
the user (ECO mode) by pressing the
22
the display activates the symbol
2 mode, press the
1
Press the On/Off button (detail 14 fig. 1).
9
12
15
25
eco
reset
comfort
• For the following 120 seconds the display will show FH which identifies the heating
system air venting cycle.
• During the first 10 seconds the display will also show the software version of the
cards:
Display card software version
Top boiler shell control unit software version
Bottom boiler shell control unit software version (model
only)
• Open the gas cock ahead of the boiler.
• When the message FH disappears, the boiler is ready to operate automatically in
case of a room thermostat demand.
. Activation of the arrows (details 18 and 24 -
eco eco
reset
comfort comfort
eco eco
reset
comfort comfort
button (detail 7 - fig. 1). In ECO mode
(detail 12 - fig. 1). To activate the COMFORT
button (detail 7 - fig. 1) again.
A
eco
reset
comfort
B C
eco
reset
comfort
. Activation
eco
reset
comfort