Bell & Ross BR 05 GMT Manual De Instrucciones página 3

ENGLISH
BR 05 GMT
BR-CAL.325 AUTOMATIC MOVEMENT
GENERAL USE
Starting the watch.
crown (turn anticlockwise) to position 1. Wind the movement by turning the crown
clockwise. After approximately 40 rotations, the watch is fully wound (the wind-
ing mechanism does not have a stop to prevent overwinding). The power reserve is
approximately 40 hours when fully wound. When the watch is worn, the automatic
mechanism will wind the movement.
fect water resistance, screw the crown back into position 0. Never operate the crown
underwater.
Power reserve.
mately 40 hours.
. Quick setting . Crown in position 2: unscrew and pull the crown out
Setting the date
to position 2 and set the date by turning the crown anticlockwise.
mechanical watches with a date function, quickset date setting MUST NOT UNDER ANY
CIRCUMSTANCES be carried out between the times of 9 PM (21.00) and 3 AM (3.00).
Slow setting . Crown in position 3: to ensure the date changes at midnight rather than
noon, it is recommended to set the date by adjusting the hands of the watch. Unscrew
and pull the crown out to position 3 and turn the hands until the date changes. Then
set the precise time.
Setting the date.
will stop, enabling the time to be set to the nearest second. Set the time by rotating
the crown in the required direction.
USING THE GMT-24H FUNCTION
Setting the time :
enabling you to set the time to the nearest second. Set the time by rotating the crown
in the required direction.
Setting Time zone 2
24H hand (C) to the hour digit of the 2nd time zone on the flange. The GMT hand moves
around the dial in 24 hours.
2 TIME ZONE DISPLAY EXAMPLE
Time zone 1
Time zone 2
A
B
C
D
E
(x4)
A.
Minute hand
B.
Hour hand
C.
Hand for the second time zone
D.
Seconds hand
E.
Case attachment screws
F.
Date
G.
Strap attachment
H.
Crown
0.
Unscrew the crown (turn anticlockwise) to position 1.
1.
Wind the movement manually (rotate clockwise).
2.
Set the second time zone (rotate clockwise).
Set the date (rotate anticlockwise).
3.
Set the time (rotate in either direction).
IMPORTANT
Magnetic fields.
Also, we would recommend that you avoid placing your watch near electronic devices
that may generate large magnetic fields (radio, smartphone, television, computer,
tablet, loudspeakers etc.).
Water resistance.
crown back to position 0. Never operate the crown underwater.
The 4 slotted screws (E) mount the bezel to the case and ensure the water
Note:
resistance of the watch. To benefit from the Bell & Ross warranty, these screws must
never be unscrewed.
MAINTENANCE
After being immersed in seawater, it is recommended to carefully rinse off the watch
and strap with fresh water. It is also recommended to have the water resistance of
your watch checked every two years.
BELL & ROSS INTERNATIONAL WARRANTY
To benefit from your 2-year international warranty, your card must be activated at the
time of purchase by your approved Bell & Ross point of sale, and presented every time
an operation is performed. You can now access the digital version of this card and all
the information relating to your watch by scanning the QR code or visiting:
www.bellross.com/warranty.
To ensure a service that meets the brand's exacting standards, any servicing of your
watch must be carried out by the Bell & Ross service centre or a watchmaker appro-
ved by Bell & Ross. The warranty does not, however, include:
. Any damage caused by accidents or by inappropriate or improper use of the watch
(e.g. violent impacts, crushing, rough handling of the clasp).
. Any damage caused by repair or disassembly operations carried out by a retailer or
after-sales service centre not approved by Bell & Ross.
. The consequences of the watch and bracelet/strap ageing and normal wear and tear.
When the watch has stopped (crown in position 0): unscrew the
Bell & Ross watches have a power reserve of approxi-
Unscrew the crown then pull it out to position 3. The seconds hand
(crown in position 3). The seconds hand will stop,
Time zone 1
(crown in position 2). Turn the crown clockwise to set the GMT-
G
(NEVER UNSCREW)
Magnetic fields can adversely affect the accuracy of your watch.
Once the watch is set, to ensure perfect water resistance, push the
: Once the watch is set, to ensure per-
NOTE
Dial: it is 10:10 in Geneva
Flange: it is 16:10 in Hong Kong
3
NOTE
0 1 2
H
F
: as with all
3