Hilti PRI 36 Manual De Instrucciones página 32

6.2.1 Charging the battery in the tool 6 7
NOTE
Take care to ensure that the temperatures during char-
ging correspond to the recommended range (0 to 40°C).
1. Insert the battery in the battery compartment.
2. Turn the catch so that the charging cord socket on
the battery pack is visible.
3. Plug the charging cord from the AC adapter or motor
vehicle power adapter into the battery.
The battery begins to charge.
4. If you switch the tool on, the state of charge will
be shown by the battery status display on the tool
while charging is taking place.
6.2.2 Charging the battery outside the tool 8
NOTE
Take care to ensure that the temperature during charging
corresponds to the recommended range (0 to 40°C).
1. Remove the battery from the tool and connect it to
the AC adapter or motor vehicle power adapter.
2. The red LED on the battery lights while charging is
in progress.
6.2.3 Charging the battery while the tool is in
operation
CAUTION
Avoid ingress of moisture. Moisture in the interior of
the tool may cause a short circuit and chemical reactions
resulting in burns to the skin or fire.
1. Swing the cover to the side so that the charging
cord socket becomes accessible.
2. Connect the charging cord from the AC adapter to
the battery.
3. The tool continues to operate while charging is in
progress.
4. During charging, the charging status is indicated by
the LEDs on the tool.
6.3 Handling batteries with care
Store the battery in a cool and dry place. Never store the
battery where it is exposed to direct sunlight or sources of
heat, e.g. on heaters / radiators or behind glass. Batteries
that have reached the end of their life must be disposed
of safely and correctly to avoid environmental pollution.
6.4 Fitting the battery 6
CAUTION
Before inserting the battery in the power tool, check
to ensure that the battery terminals and the contacts
in the power tool are free from foreign objects.
All manuals and user guides at all-guides.com
1.
2.
6.5 Removing the battery 9
1.
2.
6.6 Switching the tool on
Press the on / off button.
NOTE
After switching on, the tool begins the automatic leveling
process (takes max. 40 seconds). After completion of the
leveling process, the laser beam switches on and begins
to rotate in the normal direction. When leveling in the
horizontal plane the laser head rotates automatically at
medium speed and, when working in the vertical plane, a
reference point is projected downwards.
6.7 LED indicators
Please refer to section 2 "Description".
6.8 Inserting batteries in the PRA 36 10
CAUTION
Do not use damaged batteries.
DANGER
Do not mix old and new batteries. Do not mix batteries of
different makes or types.
NOTE
The PRA 36 may be powered only by batteries manu-
factured in accordance with the applicable international
standards.
6.9 Pairing 11
The PRI 36 rotating laser and the PRA 36 must be set
to operate as a pair before they can be used together.
Pairing the tools means that the rotating laser and PRA 36
remote control unit are configured to communicate with
each other. The PRI 36 rotating laser then receives signals
only from the PRA 36 with which it has been paired.
Pairing makes it possible to work alongside other rotating
lasers without risk of settings being altered inadvertently
by these tools.
1.
2.
Push the battery into the tool.
Turn the catch in a clockwise direction to the second
detent (the "locked" symbol is displayed).
Turn the catch in a counterclockwise direction from
the second position back to the "open" position (the
"unlocked" symbol is displayed).
Pull the battery out of the tool.
Press the on / off buttons on the PRI 36 rotating
laser and on the PRA 36 simultaneously and keep
them pressed for at least 3 seconds.
When pairing has been carried out successfully, a
signal tone is emitted by the PRA 36 and all LEDs
on the PRI 36 rotating laser blink.
At the same time, a chain symbol appears briefly
in the PRA 36 display. Both appliances switch off
automatically after pairing.
Switch on the paired tools.
The "paired" symbol appears in the display (see
"Troubleshooting" section).
en
25