Whirlpool ACQ088PV Manual De Uso Y Cuidado página 11

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Auto—automatically controls the fan speed depending on
the current room temperature and temperature control
setting
NOTE: Auto fan speed cannot be selected in Fan mode.
NOTE: After 5 seconds, the display will show the current room
temperature.
Filter Monitor
1. When the Filter Monitor indicator light is lit, remove, clean and
replace the air filter. See "Cleaning the Air Filter."
2. Press FILTER MONITOR after cleaning and replacing the air
filter. This resets the filter monitor.
NOTE: After 360 hours of fan operating time, the filter indicator
light will turn on. It will remain on for 180 hours or until you press
FILTER MONITOR. After 180 hours, it will turn off automatically.
Temperature
Press the plus TEMP button to raise the temperature. Each
time you press or hold the plus TEMP button, the
temperature will go up 2ºF (1ºC) until it reaches 90°F (32°C).
NOTE: After 5 seconds, the display will show the current
room temperature.
Press the minus TEMP button to lower the temperature. Each
time you press or hold the minus TEMP button, the
temperature will go down 2ºF (1ºC) until it reaches 64°F
(18°C).
NOTE: After 5 seconds, the display will show the current room
temperature.
All manuals and user guides at all-guides.com
Timer Delay
To set the Timer for a 30-minute to 24-hour delay until the
air conditioner turns off (the air conditioner must be On):
1. Press TIMER. Timer indicator light will flash. Display will show
remaining hours before the air conditioner will turn off.
2. Press the plus or minus TEMP button to change the delay
time from 30 minutes to 24 hours.
3. After 5 seconds, Timer indicator light will remain on. Display
will show the current room temperature.
To set the Timer to turn on the air conditioner, keeping
previous settings:
1. Turn off air conditioner.
2. Press TIMER. Timer indicator light will flash. Display will show
remaining hours before the air conditioner will turn on.
3. Press the plus or minus TEMP button to change the delay
time from 30 minutes to 24 hours.
4. After 5 seconds, Timer indicator light will remain on. Display
will show current room temperature.
To set the Timer to turn on the air conditioner, changing
previous settings:
1. Turn on air conditioner.
2. Adjust the mode to Cool, Dry, Fan or Heat (Heat/Cool models
only).
3. For Cool or Heat (Heat/Cool models only) mode:
Adjust fan speed to High, Med, Low or Auto.
Adjust temperature between 64ºF and 90ºF (18ºC and
32ºC).
4. For Fan mode, adjust fan speed to High or Low.
NOTE: In Fan mode, temperature cannot be set.
5. For Dry mode, adjust temperature up or down by 4ºF (2ºC).
6. Turn off air conditioner.
7. Press TIMER. Timer indicator light on the air conditioner
control panel will flash.
8. Press up or down arrow button to change the delay time from
30 minutes to 24 hours.
9. After 5 seconds, Timer indicator light on the air conditioner
control panel will remain on.
To clear Timer delay program:
NOTE: Air conditioner can be either on or off.
1. Press TIMER once after it has been programmed. Display will
show remaining time.
2. While the display is showing the remaining time, press TIMER
again. Timer indicator light will turn off.
To see or change the remaining time (in hours):
1. Press TIMER once after it has been programmed. Display will
show remaining time.
2. While the display is showing the remaining time, you can
press the plus or minus TEMP button to increase or decrease
the time.
3. After 5 seconds, the display will show the current room
temperature.
11

Publicidad

Tabla de contenido
loading

Tabla de contenido