Functional Description; Intended Use; Product Features; Technical Data - Berner BOS-140 Instrucciones De Servicio

All manuals and user guides at all-guides.com
OBJ_BUCH-2 609 140 340-001.book Page 2 Tuesday, September 20, 2005 10:02 AM
e) Maintain power tools. Check for misalign-
ment or binding of moving parts, breakage
of parts and any other condition that may
affect the power tool's operation. If dam-
aged, have the power tool repaired before
use. Many accidents are caused by poorly main-
tained power tools.
f) Keep cutting tools sharp and clean. Prop-
erly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool
bits etc., in accordance with these instruc-
tions and in the manner intended for the
particular type of power tool, taking into
account the working conditions and the
work to be performed. Use of the power tool
for operations different from those intended
could result in a hazardous situation.
5) Service
a) Have your power tool serviced by a quali-
fied repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Machine-specific
Safety Notes
B Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
B Take protective measures when dust can
develop during working that is harmful to
one's health, combustible or explosive. Exam-
ple: Some dusts are regarded as carcinogenic.
Wear a dust mask and work with dust/chip extrac-
tion when connectable.
B Keep your workplace clean. Blends of materials
are particularly dangerous. Dust from light alloys
can burn or explode.
B Do not work materials containing asbestos.
Asbestos is considered carcinogenic.
B Never use the machine with a damaged cable.
Do not touch the damaged cable and pull the
mains plug when the cable is damaged while
working. Damaged cables increase the risk of an
electric shock.
B Connect machines that are used in the open
via a residual current device (RCD).
B Use the machine only for dry sanding. Penetra-
tion of water into the machine increases the risk of
an electric shock.
2 609 140 340 • 20.9.05

Functional Description

Read all instructions. Failure to follow
all instructions listed below may result in
electric shock, fire and/or serious injury.
While reading the operating instructions,
unfold the graphics page for the machine
and leave it open.

Intended Use

The machine is intended for dry sanding of wood, plas-
tic, filler and coated surfaces.

Product Features

The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 Dust box, complete (filter system for fine dust)
2 Sanding plate
3 Sanding-sheet clamp
4 Sanding sheet
5 Release button for front clamping bracket
6 Front clamping bracket
7 On/Off switch
8 Outlet piece
9 Latching lever for dust box
10 Filter element (filter system for fine dust)
11 Extraction adapter*
12 Vacuum hose*
13 Perforating tool*
*Not all of the accessories illustrated or described are
included as standard delivery.

Technical Data

Orbital sander
Art. No.
Rated power input
No-load speed
Orbital stroke rate
Orbit diameter
Sanding sheet dimensions
— Adhesion via Velcro
backing
— Attachment via clamping
Sanding plate dimensions
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for nominal voltages [U] of
230/240 V. For lower voltage and models for specific coun-
tries, these values can vary.
English–2
BOS-140
022560
W 180
rpm 12000
opm 24000
mm 1.6
mm 115 x 107
mm 115 x 140
mm 113 x 105
kg 1.4
/II