Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
SHOT OF STEAM
®
FEATURE
®
• The S
S
feature provides an extra burst of steam for deep penetration of stubborn
HOT OF
TEAM
wrinkles. The S
S
®
feature can be used with dry or steam ironing provided the tank
HOT OF
TEAM
is at least 1/4 full of water and the temperature dial is set within the steam band.
• Allow the iron to heat for approximately two minutes.
• Press the white S
S
®
button several times to prime the pump.
HOT OF
TEAM
• Pump S
S
®
button another three to four times in order to clean the unit.
HOT OF
TEAM
• The S
S
®
feature is now ready for use. The S
HOT OF
TEAM
continuously with just a short pause between shots. The S
effective with the iron held in a horizontal position just above the fabric being ironed.
• If the tank runs dry, unplug the iron and refill with water. The iron may be filled with water
while it is hot. N
: It may be necessary to re-prime the pump before using the
OTE
S
S
®
feature again.
HOT OF
TEAM
®
SPRAY MIST
FEATURE
(Some Models Only)
• Use the S
M
®
feature to dampen fabrics with stubborn wrinkles.
PRAY
IST
• Press the gray S
M
®
button firmly to produce spray.
PRAY
IST
S
S
® F
A FE T Y
MART
E ATURE
(Some Models Only)
• When the iron is plugged into 120-Volt AC electrical outlet, the steady red light signals that
the iron is plugged in and is ready to be turned on.
• If the iron is left on the heel rest unmoved the iron will stop heating in 15 minutes.
The light on the handle will blink to indicate the iron has automatically shut off
and will continue blinking until the iron is restarted or unplugged.
• If the iron is left unmoved in the ironing position or accidentally tipped over, the iron will stop
heating in 30 seconds. Again, the light on the handle will blink to indicate the iron
has automatically shut off and will continue blinking until the iron is restarted
or unplugged.
• N
: If the temperature dial is turned to the Off position, the light will continue blinking
OTE
and then go off.
• To restart the iron, move the iron back and forth. Allow the iron to heat and continue ironing
as normal.
• N
: Although heat is no longer generated once the iron has automatically shut off,
OTE
allow sufficient time for the iron to cool before touching the soleplate or storing the iron.
All manuals and user guides at all-guides.com
S
®
feature can be used
HOT OF
TEAM
®
S
feature is most
HOT OF
TEAM
A
S
-O
UTO
HUT
FF
30
sec.
6
NON-STICK FINISH
(Some Models Only)
• The non-stick coating prevents sticking of fabrics and starch residue to the soleplate.
• To clean the soleplate, allow iron to cool and wipe with a soft cloth using a mild
vinegar solution.
• Do not use scouring pads, abrasives or chemical cleaning solvents as they may damage
the finish.
• N
: Scratches in the non-stick soleplate do not affect the performance of the iron.
OTE
• Turn the steam dial to DRY.
• Unplug the iron from the power outlet.
• Empty the water tank by opening the water reservoir cover and turning the iron upside down
to allow water to flow from the opening. Shake the iron gently to remove trapped water drops.
• Close cover and allow the iron to cool.
• Loop cord loosely around cord wrap. Always store iron on its heel rest.
• When not ironing, always set steam dial to DRY.
15
STEAM VALVE
min.
The steam valve (attached to the variable steam dial) is removable for easy cleaning of lint and
scale build up. Cleaning the steam valve is only necessary if you notice a reduction in steam
performance. To remove the steam valve, empty the water tank and place iron on the soleplate.
Turn the variable steam dial to CLEAN. The valve will "pop-up. " Pull up to remove the steam
valve fully. Wipe the tip gently with a damp cloth to clean. To replace, align CLEAN with the
indicator mark. Push down and rotate clockwise to the DRY.
N
: Do not pour water into the steam valve hole.
OTE
SOLEPLATE
If starch or other material clings to the iron's soleplate, allow the iron to cool and wipe with a soft,
damp cloth. Avoid ironing over snaps, zippers, rivets, etc., as they may scratch the soleplate.
STORAGE
Always store your iron on the heel rest.
Never store with the soleplate facing down
or in the carton. Always store your iron
with the steam dial turned to DRY.
Wrap cord around cord wrap.
C
E
U
ARE A F TER
ACH
SE
C
M
ARE AND
AINTENANCE
7
Publicidad
Tabla de contenido
