Teac W-790R Manual Del Usuario página 8

Synchro reverse dubbing
The SYNC REV button allows both decks to
be reversed at exactly the same time during
dubbing. This function is convenient when
using tapes with different lengths, to dub a
tape with exactly the same contents as the
original.
1. Set the tape running direction of both
decks to the ∏ (forward) direction, and
set the REV MODE switch to the π
position.
2. Press the SYNC REV button.
3. Press either of DUB START buttons
(HIGH or NORMAL).
4. The tapes in TAPE I and II travel as illus-
trated in the chart "Synchro Reverse
Dubbing Operation" on page 7.
Note:
● If the original tape is shorter than the
dubbed tape, blank sections will be left at
both ends of the dubbed tape. To prevent
this, use tapes with the same length as
far as possible.
Manual editing with REC MUTE and
PAUSE
During normal-speed dubbing, you can edit
the dubbed tape as required using the REC
MUTE and PAUSE buttons. For example,
you can record only the required tunes from
TAPE I to TAPE II skipping unwanted tunes.
● During normal-speed dubbing, when the
PAUSE button is pressed, TAPE II enters
the record-pause mode while TAPE I
continues playback. While listening to
the sound from TAPE I, when it reaches a
section you want to dub, press the
PAUSE button again to restart recording
on TAPE II.
● During normal-speed dubbing, when the
REC MUTE button is pressed, TAPE II
enters the record muting operation as in
normal recording. To restart recording on
TAPE II, press the PAUSE button.
All manuals and user guides at all-guides.com
Notes:
● The settings of the REC LEVEL control
and DOLBY NR switch are ignored during
dubbing as they have no effect.
● The , ", ∏ and Ò buttons do not
function during NORMAL speed or HIGH
speed dubbing. Also, REC MUTE and
PAUSE do not function during HIGH
speed dubbing.
● The sound quality of the dubbed tape
may be slightly worse than that of the
original tape. For this reason, multigener-
ation dubbing is not recommended.
● If there is a TV set near the cassette deck
during high speed dubbing, it is possible
that the TV's horizontal scanning fre-
quency may be recorded on the tape. If
this occurs or to prevent it in advance,
dub at normal speed, switch off the tele-
vision or keep the deck a reasonable dis-
tance away from the TV.
Timer-Controlled Operation (Fig. 6)
By using the deck with an audio timer,
tapes can be recorded or played back at
any preset time. If tapes are loaded in both
decks, you can also start continuous play-
back in this way.
Timer recording
Recording a broadcasting program:
1. Connect the deck and stereo system to
a commercially available audio timer as
shown in the diagram. (Fig. 6)
2. Set the power switches of all compo-
nents to ON.
3. Load a recordable cassette in TAPE II.
4. Set the REV MODE switch to the
required position. (Refer to " Tape Travel
Depending on Setting of REV MODE
Switch" on page 5.)
5. Set the TIMER switch to the REC posi-
tion.
6. Tune to the broadcasting station to be
recorded.
7. Press the RECORD button to set the
deck to the record-pause mode.
8. Adjust the recording level with the REC
LEVEL control as explained on page 7.
9. Set the DOLBY NR switch as required.
10. Set the audio timer to the required start
(power on ) and stop (power off) times.
When this setting is completed, the
power to all components will be
switched off.
When the preset start time is reached,
power will be supplied and recording will
start (to ∏ direction) automatically.
_ 8 _
Timer playback
1. Connect the deck and stereo system to
a commercially available audio timer as
shown in the diagram. (Fig. 6)
2. Set the power switches of all compo-
nents to ON.
3. Load pre-recorded cassette(s) in TAPE
I or II (or both).
4. Set the REV MODE switch to the
required position. (Refer to "Tape Travel
Depending on Setting of REV MODE
Switch" on page 5.)
5. Set the TIMER switch to the PLAY posi-
tion.
6. Set the DOLBY NR switch as desired.
7. Set the audio timer to the required start
(power on) and stop (power off) times.
When this setting is completed, the
power to all components will be
switched off.
When the preset start time is reached,
power will be supplied and playback will
start (to ∏ direction) automatically.
Notes:
● When cassettes are loaded in both
decks, TAPE I will start playback first
because it has priority.
● Be sure to set the TIMER switch to the
OFF position after timer operation is
completed.