Description Of The Device; Technical Data; Working With The Device - Proxxon PS 13 Manual

Ocultar thumbs Ver también para PS 13:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 16
h) Only allow trained personnel to use the
power tool.
Apprentices may only operate the power tool
when they are aged over 16, when this is
necessary for their training and when they
are supervised by a trained operative.
4.) Power tool use and care
a) Do not force the power tool. Use the cor-
rect power tool for your application.
The correct power tool will do the job better
and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch
does not turn it on and off correctly.
Any power tool that cannot be controlled
with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power
source before making any adjustments,
changing accessories, or storing power
tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfa-
miliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools carefully. Check for
misalignment or binding of moving parts,
breakage or damage of parts
and any other condition that may affect
the power tools operation. If damaged,
have the power tool repaired by a
qualified expert before use.
Many accidents are caused by poorly main-
tained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to
bind and are easier to control.
g) Secure the workpiece.
Use clamps or a vice to hold the workpiece.
This is safer than holding it with your hand,
and also it frees both hands
to operate the equipment.
h) Use the power tool, accessories and tool
bits etc., in accordance with these
instructions and in the manner specified
for the particular type of power tool, tak-
ing into account the working conditions
and the work to be performed.
Use of the power tool for operations different
- 8 -
All manuals and user guides at all-guides.com
5.) Service
a) Have your power tool serviced by a quali-
b) Comply with maintenance instructions
c) Check mains lead of power tool regularly

Description of the device

General:
The super fine grinding device with linear grind-
ing surface is ideal for machining surfaces in
recesses, slits, compartments, small corners.
In a nutshell: Everywhere where it is extremely
tight.
The device has four grinding inserts (straight
and angled) with variously formed surfaces.
In addition to suitable, self-adhesive sandpaper
(watertight, grain 180, grain 240 and grain 400).
5 x 4 different forms are prestamped on each
sheet.

Technical data:

Voltage 12-18 volts DC
Power approx. 10 Watt
No. of strokes 7,000/min.
Noise development = 70 dB (A).
Feed (spiral cable) with connector safeguarded
against reverse polarity, approx. 100 cm long.
For operation, DC current of 12 – 18 volts at a
minimum of 1 A is required.
We recommend the PROXXON power supply
units NG 2 (E) or NG 5 (E).

Working with the device:

Mounting the grinding inserts
Separate the grinding inserts at the breaking
point (arrow) from the carrying material (fig. 1).
Turn the clamping mechanism of the device 1
(fig. 2) to the left by 90° up to the limit stop and
push in the insert.
from those intended could result in a
hazardous situation. All unauthorized modifi-
cations to the power tool are prohibited for
safety reasons.
fied repair person using only identical re-
placement parts.
This will ensure that the safety of the
power tool is maintained.
and instructions on tool replacements.
and have it replaced by a qualified expert
in case of damage.
Note:

Publicidad

Tabla de contenido
loading

Tabla de contenido