Front Axle - Orbea BLUE PAPER TERRA OMR 2022 Manual Tecnico

ø52.1
24 | O R BEA
H EADS ET
HEADSET SPARE PARTS AND ASSEMBLY
4.1
4.2
3
ø52.1
2.2
ø56
2.1
1.1
GREASE
1.1
1.2
01 H EA D S ET I C R B EAR I N G S 2 0 22
ART Nº: XA41
1.1 Headset bearing 1.5 (52x40x7mm.
45º/45º)
1.2 Fork crown race 1.5 45º. FSA H6106
03 H EA DS ET C OV E R I C R TE R R A OM R
ART Nº: XA54
Headset cover ICR Terra OMR
T ECHNI CAL M ANUAL
USE OF THE HEADSET EXPANDER ON CARBON
FORKS
On carbon steerer tube forks, always use an expander insi-
de the steerer tube to thread the headset compression bolt.
Never use a starnut on carbon sterer tubes. It will damage
the material and cause component failure which can lead
to serious injuries.
Consult the installation and torque settings instruction in
the expander manufacturer instructions.
Consult the instructions about the use of headset spacers
on bikes with carbon steerer tubes in the Use Warnings sec-
tion of this manual.
0 2 CO MP RE SSIO N RIN G 1 -1 /8 I CR 2 0 22 + SH IM
QTY. ART Nº: XA42
Compression ring 1-1/8 ICR 2022 + shim
2
1
0 4 I CR HEA DSET SPAC E R KI T. OVAL
QTY. ART Nº: X063
1 4.1 Headset spacer ICR oval 5mm
4.2 Headset spacer ICR oval 10mm
B LUE PAP ER T ERR A · O M R 2 0 22
R EA R AX L E A N D D E RA I L L E U R HA NG E R
REAR AXLE
6
GREASE
8 N.m
7.1
7.2
Always follow the recommended
torque settings
0 5 R EAR D ER AI LLE UR HA N G ER N º5 3 X 1 2 R OAD ST D
ART Nº: XA44
Rear derailleur hanger Nº53 X12 ROAD STD
0 7 T HR U-AXL E R OAD 12 x1 65 m m
D OU B LE L EAD TH R EA D 2 P 1 . 0 x1 5 m m
Inner thread for mudguard attachment
ART Nº: XA55
QTY.
7.1 Thru-axle 12x165x2P1.0x15mm M/guard
1
thread
7.2 Axle washer 12mm
Terra OMR is only compatible with Speed Release thru-axles with a double-lead 2P1.0 thread pitch for faster
QTY.
wheel changes. The use of axles with other thread pitch will damage the frame.
1
1
The Terra OMR dropouts are not open at the bottom, and therefore they are not compatible with the use
of Mavic Speed Release axles, since it is necessary to remove the axle completely to remove the wheels.

FRONT AXLE

17
5
8 N.m
6
0 6 HA N G ER M 18 N UT N º 0 2 X1 2 R OA D
QTY. ART Nº: X049
1 Hanger M18 NUT Nº02 X12 ROAD
0 8 T HR U-AX L E R OAD 1 2x 1 19 m m
D O UB L E L EA D T HR EA D 2 P 1 . 0 x1 3 m m
Inner thread for mudguard attachment
QTY. ART Nº: X074
8.1 Thru-axle 12x119x2P1.0x13mm M/guard
1
thread
1 8.2 Axle washer 12mm
O RBEA | 2 5 2 5
E N
GREASE
8.2
6
8.1
8 N.m
QTY.
1
QTY.
1
1