Unpacking The Device; Initial Operation; Using The Device - Clatronic DR 3431 Instrucciones De Servicio

13 Hook for cable storage
14 Measuring beaker
15 Carpet glider
16 Floor cloth
Not shown:
Screw (in the bag with the instruction manual)

Unpacking the Device

• Remove the main device and accessories from the box.
• Also remove any packaging materials that may be present.
• Check the scope of delivery.
• Fold out the handle (1) until it audibly clicks into place.
NOTE:
The handle can be folded up again for transport (Fig. E). To
do so, press the two release buttons (3). The appliance can
be easily lifted with the carrying handle (5).
Install the Base (Fig. A)
NOTE:
Look carefully at the holes (7) on the appliance foot and the
foot socket of the appliance. They must lie directly above one
another.
1. Insert the unit all the way to the base.
2. Insert the fixing screw into the hole of the base seat and
tighten it with a Phillips screwdriver.

Initial Operation

Install the Floor Cloth (Fig. B)
1. Place the base (7) in the center of the floor cloth.
2. Attach the floor cloth with the Velcro straps to the base.
3. Press to close the cord clip and at the same time tighten
the cover with the cord.
4. Loosen the cord and the Velcro straps to remove the cloth.
WARNING: There is a danger of injury!
Wait until the appliance has cooled before removing the
steam pad.
Fill in Water (Fig. C)
NOTE:
• The maximum filling capacity is 550 ml.
• Recommendation: Use distilled water to prevent calcifi-
cation.
• You can also remove the water tank from the unit for
filling.
1. Open the water tank plug (9) and fill the water tank with
water. Use the supplied measuring cup (14) to avoid
damaging the unit.
2. Close the water tank again.
Electrical Connection
• Before inserting the plug into the socket. Make sure that
the mains voltage to be used matches that of the device.
You can find this information on the nameplate.
• Connect the device to a duly installed protective contact
socket.
Connected Wattage
The station has a total maximum wattage of 1500 W.
CAUTION: Overload!
• If you use extension leads, these should have a cable
cross-section of at least 1.5 mm² .
• Do not use any multiple sockets, as this device is too
powerful.

Using the Device

CAUTION:
Before you begin cleaning you should test the materials to be
cleaned as to their suitability for cleaning with steam. Do not
hold the steam nozzle for too long and too close in one posi-
tion.
Operate the unit
1. Fill water into the water tank.
2. Attach the floor cloth.
3. Place the unit onto the carpet glider (15) (Fig. D) to clean
carpets.
4. Connect the appliance to a properly installed earthed
socket.
5. Turn the steam volume control (4) clockwise as far as it will
go, up to the maximum setting.
NOTE:
If the steam volume control is not on the maximum set-
ting, the steam volume is too low.
6. Press the on/off switch (2) to switch on the appliance. The
mains power indicator (6) lights up. The appliance is ready
for use after approx. 30 seconds. The pump begins to
work.
7. Set the required steam volume with the steam volume
control.
8. Slowly push the unit over the areas to be cleaned.
Filling the Water Tank during Operation
No steam will be discharged if the water tank is empty. The
water has to be filled up as follows:
1. Press the on/off switch (2) to switch the unit off.
2. Remove the mains plug from the socket!
3. Fill fresh water into the tank as described in the chapter
"Fill in Water (Fig. C)".
4. Reconnect to the mains power supply and press the
On/Off button to switch the unit on.
25