Grease Filter - Fagor 7CFT-NERO ISL Montaje Y Modo De Empleo

of the charcoal filter must be selected while the motor
and light are OFF.
Charcoal filter excluded: the filter alarm is disabled.
Enabling/disabling the sound signal
The sound signals may be activated or deactivated by
pressing and holding the "Light" button for 5 seconds.
If the sound signal has been activated, it should emit a
beep and the text "Snd" should appear on the display for
2 seconds.
If the sound signal has been deactivated, the text "Snd"
should appear on the display for 2 seconds and no beep
should be emitted.
Temperature alarm
The hood is fitted with a temperature sensor which
activates the motor at speed level 2 in the event that the
temperature in the display area exceeds 70°C (the
system monitors the data recorded by the sensor every
250 ms).
If the motor is OFF or at speed level 1 and the alarm
intervenes, the motor will move to speed level 2 and the
text "care" will appear on the display. While the
appliance is in its alarm operating status, the user may
only increase the motor speed (3 rd and 4 th levels). When
the temperature of the cooker hood returns to a level
below the alarm threshold, the motor will return to the
status which was set before the alarm condition occurred.
3 minutes after the intervention of the alarm, the system
will check the temperature in the display area again: if it
is lower than 70°C, the operating conditions set prior to
the intervention will be restored.
Maintenance
ATTENTION! Before performing any maintenance operation,
isolate the hood from the electrical supply by switching off at
the connector and removing the connector fuse.
Or if the appliance has been connected through a plug and
socket, then the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products. DO NOT USE ALCOHOL!
WARNING:
Failure to carry out the basic cleaning recommendations of the
cooker hood and replacement of the filters may cause fire
risks.
Therefore, we recommend oserving these instructions.
The manufacturer declines all responsibility for any damage to
the motor or any fire damage linked to inappropriate
maintenance or failure to observe the above safety
recommendations.
All manuals and user guides at all-guides.com
7

Grease filter

Fig. 2
This must be cleaned once a month (or when the filter
saturation indication system – if envisaged on the model in
possession – indicates this necessity) using non aggressive
detergents, either by hand or in the dishwasher, which must
be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolour
slightly, but this does not affect its filtering capacity.
To remove the grease filter, pull the spring release handle.
Charcoal filter (filter version only)
Fig. 3
It absorbs unpleasant odours caused by cooking.
The charcoal filter can be washed once every two months (or
when the filter saturation indication system – if envisaged on
the model in possession – indicates this necessity) using hot
water and a suitable detergent, or in a dishwasher at 65°C (if
the dishwasher is used, select the full cycle function and leave
dishes out).
Eliminate excess water without damaging the filter, then put it
in the oven for 10 minutes at 100° C to dry completely.
Replace the mattress every 3 years and when the cloth is
damaged.
Remove the filter holder frame by turning the knobs (g) 90°
that affix the chimney to the cooker hood.
Insert the pad (i) of activated carbon into the frame (h) and fit
the whole back into its housing (j).
It is possible to use a traditional carbon filter,
washable nor regenerable, to be replaced every 3 - 4 months.
The filter holder frame of the carbon filter is welded together;
the eventual frame supplied with the hood is not, therefore, to
be used.
Insert it into its housing and fix it turning the 2 plastic knobs.
Replacing lamps
Fig. 4
Disconnect the hood from the electricity.
Warning! Prior to touching the light bulbs ensure they are
cooled down.
• Use a small screwdriver as a lever on the borders of the
lamp in order to remove the lightbulb.
• Slide out the lightbulb to be replaced and replace with a
new 12V 20W 30° Ø35 12V GU4.
• Carry out the replacement and mount the new lightbulb
by following instructions in the reverse.
If the lights do not work, make sure that the lamps are fitted
properly into their housings before you call for technical
assistance.
neither