Description Of The Hood; Control Panel - Fagor 7CFT-NERO ISL Montaje Y Modo De Empleo

Description of the hood

Fig. 1

1. Control panel

2. Grease filter
3. Grease filter release handle
4. Halogen lamp
5. Vapour catcher
6. Telescopic chimney
7. Air outlet (used for filter version only)
Operation
Use the high suction speed in cases of concentrated kitchen
vapours. It is recommended that the cooker hood suction is
switched on for 5 minutes prior to cooking and to leave in
operation during cooking and for another 15 minutes
approximately after terminating cooking.
Control panel
1. Timer button
The timer value can be increased or decreased in steps of 1
minute; the default time period is set to 10 minutes.
The value can be set to a time period of anywhere between 20
minutes and 1 minute.
Within 5 seconds of the "TIMER" button being pressed, the
system will enter its programming mode and the user will be
able to set the timer countdown period using the "-" and "+"
buttons. If none of the buttons are pressed within a period of 5
seconds from when the Timer function was selected or the
time period programmed, the countdown will begin.
The timer countdown can be activated as follows:
- after pressing the TIMER button for the first time
(default time value);
- by pressing the TIMER button within 5 seconds of
setting the desired countdown time period.
Once the timer has begun counting down, it may be cancelled
by pressing the TIMER button.
2. Light button
Light ON/OFF button.
3. Display
Indicates the status of the hood.
4. "-" Decrease motor speed / OFF button
The OFF status can be achieved by pressing the "-"
button and decreasing the motor speed until it stops.
5. "+" Increase motor speed / ON button
The ON status can be achieved by pressing the "+"
button; the motor will start at the lowest speed level.
The speed sequence is 1-2-3-4, therefore every time the
"+" button is pressed the motor moves on to the next
speed level.
If the motor is at the 4 th speed level and the "+" button is
pressed, you will hear a beep.
All manuals and user guides at all-guides.com
6
The 4 th motor speed level is the intensive function and is
timer-operated.
The standard period of time is 5', at the end of which the
hood reverts to speed level 2.
To deactivate the function before the set time has elapsed,
simply press the "-" button.
SPECIAL FUNCTIONS
Programming the Clock
The clock may be set at any time, apart from when the
timer function is active.
The clock may be displayed in a 12-hour format, indicating a
time between 1:00 and 12:59.
The clock may be reset by pressing and holding the
"Timer" button for 5 seconds, then pressing the "-" and
"+" buttons to adjust the time.
The user may increase/decrease the time in steps of 1
minute; however, if the "-" or "+" button is pressed for 1
second, the time is decreased/increased in steps of 5
minutes. In this case, the control panel rounds the time
off to the nearest 5 minutes.
The user can end the clock resetting stage by pressing
the "Timer" button.
If none of the buttons are pressed for 1 minute, the control
panel accepts the set value and adds on 1 minute, then
begins to operate normally.
Grease filter warning
After 40 hours of operation, "Grease Filter" appears on the
display. When this text appears, the filter needs to be washed.
To reset the grease filter warning, the user should press
and hold the "+" button for 5 seconds. After this action,
the "Grease Filter" text will disappear, a "beep" will be
emitted to indicate the process is compete and the
display will return to showing its normal operating
functions.
The grease filter counter will reset after this procedure is
complete.
Charcoal filter warning
After 160 hours of operation, "Charcoal Filter" appears on the
display. When this text appears, the filter needs to be
replaced.
To reset the charcoal filter warning, the user should press
and hold the "-" button for 5 seconds. After this action,
the "Charcoal Filter" text will disappear, a "beep" will be
emitted to indicate the process is compete and the
display will return to showing its normal operating
functions.
The charcoal filter counter will reset after this procedure is
complete.
Enabling/disabling the charcoal filter warning
The charcoal filter may be enabled or disabled by
pressing and holding the "-" and "+" buttons
simultaneously for 5 seconds. The inclusion or exclusion