Ec Declaration Of Conformity - BTI A18 DSS-1 BL 1/2 Manual Original

Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household
refuse or by burning them. BTI off er to retrieve old batteries
to protect our environment; please ask your sales
representative or our service line at 07940 / 141-141.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System BTI chargers for charging System BTI
battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store
only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under
extreme load or extreme temperatures. In case of contact
with battery acid wash it off immediately with soap and
water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and
product damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to fl ow
inside them. Corrosive or conductive fl uids, such as
seawater, certain industrial chemicals, and bleach or bleach
containing products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The cordless impact wrench can be used to tighten and
loosen nuts and bolts wherever no mains connection is
available.
Do not use this product in any other way as stated for
normal use.
RPM SETTING
The function is designed to give the user greater control
in application and reduce damage to the fastener or work
surface by automatically shutting the tool off after the tool
senses the mechanism impacting for approximately one
second.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
regulations and the directives 2011/65/EU (RoHS), 2014/30/
EU, 2006/42/EC, and the following harmonized standards
have been used:
EN 62841-1:2015
EN 62841-2-2:2014
EN IEC 55014-1:2021
EN IEC 55014-2:2021
EN IEC 63000:2018
Ingelfi ngen, 2021-05-11
Michael Nagel ppa. Martin Mayer-Hagelstein
Managing Director Director Marketing & E-Commerce
Authorized to compile the technical fi le
BTI Befestigungstechnik GmbH & Co. KG
Salzstraße 51
D-74653 Ingelfi ngen
ENGLISH
457 823 - BTI-A18DSS-1BL12 .indd 16 457 823 - BTI-A18DSS-1BL12 .indd 16
OPERATION
Note: It is recommended after fastening to always check
the torque with a torque wrench.
The fastening torque is aff ected by a wide variety of factors
including the following.
• State of battery charge – When the battery is discharged
voltage will drop and the fastening torque will be reduced.
• Operation at speeds – Operating the tool at low speeds
will cause a reduction in fastening torques.
• Fastening position – Holding the tool or the driving
fastener in various angles will aff ect the torque.
• Drive accessory/socket – Failure to use the correct size
accessory or socket, or a non-impact rated accessory may
cause a reduction in the fastening torque.
• Use of accessories and extensions – Depending on the
accessory or extension fi tment can reduce the fastening
force of the impact wrench.
• Bolt/Nut – Fastening torques may diff er according to the
diameter of the nut or bolt, the class of nut/bolt and the
length of nut/bolt.
• Condition of the fastener – Contaminated, corroded, dry or
lubricated fasteners may vary the fastening torques.
• Condition and base material – The base material of the
fastener and any component in between the surfaces may
eff ect the fastening torque (dry or lubricated base, soft or
hard base, disc, seal or washer between fastener and
base material).
IMPACTING TECHNIQUES
The longer a bolt, screw, or nut is impacted, the tighter it will
become.
To help prevent damaging the fasteners or workpieces,
avoid excessive impacting.
Be particularly careful when impacting smaller fasteners
because they require less impacting to reach optimum
torque.
Practice with various fasteners, noting the length of time
required to reach the desired torque.
Check the tightness with a hand-torque wrench.
If the fasteners are too tight, reduce the impacting time.
If they are not tight enough, increase the impacting time.
Oil, dirt, rust or other matter on the threads or under the
head of the fastener aff ects the degree of tightness.
The torque required to loosen a fastener averages 75% to
80% of the tightening torque, depending on the condition of
the contacting surfaces.
On light gasket jobs, run each fastener down to a relatively
light torque and use a hand torque wrench for fi nal
tightening.
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure
to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, after use, the battery packs have
to be fully charged.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
16
18.05.2021 09:34:52 18.05.2021 09:34:52