Assembly And Operation; Problem Solution - Worx WX175 Manual Original

OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE (FOR WX175 WX175.1
WX175.2 WX175.9)
The machine is intended for driving in and
loosening screws as well as for drilling in wood,
metal and plastic.
INTENDED USE (FOR WX373 WX373.1
WX373.2 WX373.3 WX373.4 WX373.5
WX373.9)
The machine is intended for impact drilling in brick,
concrete and stone as well as for drilling in wood,
metal and plastic.
ASSEMBLY AND
OPERATION
ACTION
BEFORE OPERATION
Checking the battery charge
condition (Only for WX373
WX373.1 WX373.3 WX373.4
WX373.5 WX175 WX175.1)
12
Removing the battery pack
Charging the battery
Installing the battery pack
ASSEMBLY
CHUCK ADJUSTMENT
WARNING: Always lock off trigger switch and
disconnect tool from power source when
changing accessories. Always ensure the bit is secure
before starting the tool. Damage to the Chuck or a
loose bit may cause possible personal injury.
-- Removing the bits
-- Inserting the bits
Assembling the belt hook and
bit clip
OPERATION
FORWARD/REVERSE
ROTATION CONTROL
WARNING: Never
change the direction of
rotation when the chuck is
rotating, wait until it has
stopped!
Lithium-Ion Brushless drill driver
Lithium-Ion Brushless hammer drill
TWO-SPEED GEAR
CONTROL
TORQUE ADJUSTMENT
SCREWDRIVING,
DRILLING, HAMMER
DRILLING
OPERATING THE ON/OFF
SWITCH
at low speed because excess
heat will be produced
internally.
LED LIGHT INDICATOR (See Fig. G)
Before operation, the LED light will be activated
when the On/Off switch is slightly depressed, and
will automatically turn off 20 seconds after the On/Off
switch is released.
Reverse Rotation Control is on right/left position.
FIGURE
The tool and battery are equipped with a protection
system. When the LED Light is quickly flashing 60
seconds and turn off, the system will automatically
cut off power to the tool to extend battery life. The
tool will automatically stop during operation if the
See Fig. A1
tool and/or battery are placed under one of the
following conditions:
• Overloaded: The tool is operated in a manner that
See Fig. A2
causes it to draw an abnormally high current. In this
situation, release the Trigger Switch on the tool and
See Fig. A3
stop the application that caused the tool to become
overloaded. Then pull the Trigger Switch again to
See Fig. A4
restart.
• Overheated: Under the condition above, if the tool
does not start, the Tool and Battery are overheated.
In this situation, let the Tool and Battery cool before
pulling the Trigger Switch again.
• Low battery voltage: The remaining Battery capacity
is too low and the tool will not operate. In this
situation, remove and recharge the Battery.
See Fig. B1

PROBLEM SOLUTION

See Fig. B2
1. WHY DOES THE DRILL NOT TURN ON WHEN
See Fig. C1, C2,
YOU PRESS THE SWITCH?
C3, C4
The Forward and Reverse Switch, which is on top of
the trigger, is positioned in the lock function. Unlock
the Forward and Reverse Switch putting it into the
required rotation position. Push the trigger and the
drill will start to rotate (See Fig. B).
See Fig.D1, D2,
2. THE DRILL STOPS BEFORE THE SCREW IS
D3
COMPLETELY TIGHTENED. WHY?
Verify the torque position of the Torque Adjustment
Ring, you can find the Torque Adjustment Ring
between the Chuck and the drill body. Position
WARNING: Do not
operate for long periods
WARNING: To turn on the light, press the
On/Off switch and make sure the Forward/
See Fig. E
See Fig. F1, F2, F3
See Fig. G
EN