Oki MPS930b Manual Del Usuario página 3

Safety Information,
220/240-Volt Models
This product has been carefully designed to give years of
safe, reliable performance. As with all electrical equipment,
however, there are a few basic precautions that should be
taken to avoid injury or damage:
Ensure this and all other documentation is both read carefully
and retained for future reference.
Ensure all warning and instruction labels on the product are
read, understood and followed in order to prevent any risk of
injury.
This product may be heavy. Please check the weight of the
product and take all necessary precautions to prevent the risk
of personal injury.
The product must be placed on a flat solid surface strong
enough to support its weight to prevent any risk of injury.
Ensure that there is adequate ventilation all around the
product to prevent overheating and any risk of fire.
Keep the product away from direct heat sources such as
radiators and out of direct sunlight to prevent any risk of
overheating.
The power supply required for this product is 220-240 VAC,
50/60 Hz. (For any DC powered product, the figures are 9.6-
31.2VDC, 4-1.8A.) Refer to your product's rating label on the
machine for full power rating details. Ensure that you have a
suitable power supply before connecting the product. If in
doubt contact your dealer or check with your local power
provider.
Ensure both the product and mains power switches are in the
OFF position before connecting the AC power cable.
Do not connect or disconnect the power plug with a wet hand
as this may cause electric shock.
Always hold the power plug to connect/disconnect the power
cable to/from the mains socket. Unplugging by pulling on the
cable can cause fraying and may lead to fire or electric shock.
This product has an earthed plug as a safety feature and will
only connect to an earthed socket. Do not attempt to defeat
the earthing or there is a risk of fire or shock.
If using an extension cable or power strip ensure that the total
current rating (amperes) of all connected equipment is less
than the maximum rating of the extension cable, power strip
or wall outlet. If the product is already supplied with a fitted
power strip then no additional power strip or extension cable
should be used to connect to the mains wall outlet. Otherwise,
fire or shock may occur.
Ensure the power cable is routed so as not to be damaged or
cause a trip hazard. If the cable becomes frayed or damaged
replace it immediately to prevent any risk of shock.
Do not twist, constrict or knot the power cable as this can
cause overheating which may lead to fire or electric shock.
Ensure the power socket to which the product is connected is
easily accessible at all times and not obstructed.
Use only the power cable supplied. Using a power cable not
intended for this product may lead to fire or electric shock.
To avoid risk of fire and electric shock, do not use the power
cable supplied with this product for any other electrical
equipment.
If you do not connect the power cord or any other cables only
as directed in the User's Guide, this may result in a fire.
It is recommended that the machine is switched off prior to
opening covers; otherwise there is a risk of electric shock.
When the product cover is open, do not touch the fuser unit or
print head as you may receive burns. Allow it to cool before
touching.
If the product casing gets extremely hot or smoke, unusual
smells or abnormal noises are emitted from the product, there
is a risk of fire. Unplug the mains connector and contact your
dealer.
If the product has been knocked over or damaged, there is a
risk of electric shock, fire and/or injury. Unplug the mains
connector and contact your dealer.
If any liquid (for example water) is allowed to enter the
product, there is a risk of fire. Unplug the mains connector
and contact your dealer.
Do not place containers containing liquid on the product as
electric shock, fire and/or injuries may occur.
If any foreign objects (for example clips) are allowed to enter
the product, there is a risk of electric shock, fire and/or injury.
Unplug the mains connector before removing the object.
Do not introduce foreign objects into the ventilation holes or
operate this product with any covers open or doors removed as
electric shock, fire and/or injuries may occur.
Do not use an extremely flammable spray near the product as
the product contains high temperature parts that may cause a
fire.
Switch the product off before cleaning to prevent any risk of
injury. Clean using a damp cloth. Do not use liquid or aerosol
cleaners.
Ensure loose clothing and hair is kept clear of moving parts
when the product is in operation to prevent possible risk of
injury.
Do not carry out any operations on the product that are not
specified in the User's Guide. This may result in electric shock,
fire and/or injury.
Do not touch the battery if one is fitted to the product. There
is a risk of explosion if the battery is replaced by an incorrect
type. The product battery should not require replacement
during the life of the product.
Do not throw toner cartridges or image drum cartridges into a
fire as you may receive burns from a dust explosion.
After installing additional memory, hard disk drive, or any
other internally fitted option, any covers removed or doors
opened must be closed or replaced and secured to prevent
risk of fire.
The acoustic noise of this product is less than 70 dB (A) as
measured in accordance with EN ISO 7779.
The operating condition range for your product is: 10 to 32°C
and 20 to 80% RH. Operation of the product outside this
range could result in damage to the product.
If a scanner, finisher etc. is fitted, exercise care when moving
these items so as to avoid risk of entrapment or personal
injury.
If the product is installed on a cabinet or high capacity feeder,
ensure wheel locks are applied once placed in final position for
use, to prevent risk of movement or injury.
3 - English