Inserting A Blank Space During Recording (Record Muting); Additional Information; Precautions - Sony TC-KE300 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Advanced Recording Operations
Inserting a Blank Space During
Recording (Record Muting)
You can insert a blank space of 4 seconds between each
track. The blank spaces between tracks let you locate
the track easily with the Multi-AMS function (see page
8). Also, use this function to eliminate only unwanted
portions on the tape.
·
RESET
MEMORY
0
AMS
)
·
0
)
POWER
p
P
R
r
PAUSE
REC MUTE
REC
P PAUSE
R REC MUTE
1
Start recording.
2
Press R REC MUTE once when you want to
insert a blank space.
"REC" in the display starts flashing and the tape
moves on without recording any signals.
After 4 seconds, "P" lights up and the tape deck
is now ready to resume recording.
3
Press P PAUSE or · to resume recording.
z
To insert a blank space longer than 4 seconds
Hold down R REC MUTE as long as you want. After 4
seconds, "REC" in the display flashes faster.
When you release the R REC MUTE , "P" lights up and
the tape deck is ready to resume recording.
Press P PAUSE or · to resume recording.
z
To insert a blank space of less than 4 seconds
After pressing R REC MUTE, press P PAUSE at any
time. The deck changes to recording pause. To resume
recording, press r REC instead of P PAUSE.
10
EN

Additional Information

Precautions

On safety
• Do not disassemble the cabinet — this may result in an
electrical shock. Refer servicing to qualified personnel
only.
• Should any solid object or liquid fall into the cabinet,
unplug the tape deck and have it checked by qualified
personnel before operating it any further.
On power sources
• Before operating the tape deck, check that the operating
voltage of the tape deck is identical with your local power
REC LEVEL
5
4
6
3
7
supply. The operating voltage is indicated on the
AUTO CAL
DOLBY NR
BALANCE
OFF
2
8
B
B
C
C
1
9
MPX
L
R
0
10
nameplate at the rear of the tape deck.
FILTER
PHONES
EJECT
§
• The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet, even if
the unit itself has been turned off.
• If you are not going to use the tape deck for a long time,
be sure to disconnect the tape deck from the wall outlet.
To disconnect the AC power cord (mains lead), grasp the
plug itself; never pull the cord.
• AC power cord must be changed only at the qualified
service shop.
On operation
• Because of a safety mechanism, the function buttons will
not operate if the cassette holder is not completely closed,
if there is no cassette in the cassette holder, or if a cassette
has been incorrectly inserted into the cassette holder.
• Be sure to stop the tape before turning off the tape deck.
Otherwise, the tape may be damaged.
On placement
• Place the tape deck in a location with adequate ventilation
to prevent heat build-up in the tape deck.
• Do not place the tape deck:
— on a soft surface such as a rug that might block the
ventilation holes on the bottom.
— in a location near heat sources.
— in a place subject to direct sunlight.
— in an inclined position.
— in a place subject to excessive dust or mechanical shock.
On cleaning the tape deck
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do not
use any type of abrasive pad, scouring powder or solvent
such as alcohol or benzine.
If you have any questions or problems concerning your
tape deck, please consult your nearest Sony dealer.
For the customers in the U.S.A.
For detailed safety precautions, see the leaflet
"IMPORTANT SAFEGUARDS."
3-856-134-51(1)

Publicidad

Tabla de contenido
loading

Tabla de contenido