Philips AJ 3225 Guia De Inicio Rapido

Clock Radio
AJ 3225 - Clock radio
English
Français
Español
Deutsch
Nederlands
Italiano
Meet Philips at the Internet
http://www.philips.com
Printed in Hong Kong
2
1
9 8
All manuals and user guides at all-guides.com
AJ 3225
CONTROLS
1 SLEEP - activates the radio for sleep function
- adjusts the sleep period
2 Clock control
- CLOCK : to run on clock time
- SET ALARM 1 : sets the alarm time for alarm 1
- SET ALARM 2 : sets the alarm time for alarm 2
- SET TIME : sets the clock time
7
/ ∞ : adjusts the hours/ minutes for the clock and alarm times
-
3 /REPEAT ALARM
SLEEP OFF
- switches off the radio sleep function
- switches off the active alarm for a 6-7 minute period
4 Frequency indicator - shows the radio frequency of your selected waveband
5 TUNING - tunes to radio stations
6 BAND - select FM/MW (AM or LW) waveband
7 VOLUME - adjusts the sound level
8 ALARM RESET - stops the active alarm for 24 hours
9 DISPLAY - show the clock/ alarm times and status of the set
0 RADIO - switches the radio off/on
/
OFF ON
! ALARM 1 , ALARM 2
– OFF switches off the alarm 1 or alarm 2
– RAD activates the radio for alarm 1 or alarm 2
– BUZ activates the buzzer for alarm 1 or alarm 2
@ Battery door - opens to store a 9 volt 6F22 type battery (not included) for
clock memory backup
# Mains lead - for AC mains supply
$ Pigtail aerial - improves FM reception
RADIO
You can use this set solely as a radio!
1 Adjust RADIO
/
OFF ON
2 Select your waveband by adjusting the BAND switch.
3 Adjust TUNING to tune to your desired station.
4 Turn the VOLUME control to adjust the volume level.
5 Adjust RADIO
/
OFF ON
To improve reception:
FM: extend and position the pigtail for optimum reception.
AM:
uses a built-in aerial inside the set. Direct the aerial by adjusting the
position of your set.
SETTING THE CLOCK AND ALARM TIMES
The time is displayed using the 24-hour clock
IMPORTANT! To adjust the clock and alarm times accurately, always make sure
you press the
1 Turn the clock control to SET TIME or SET ALARM 1 or SET ALARM 2 to
set the clock or alarm time respectively.
7
or ∞ repeatedly or hold down on the respective button to adjust the
2 Press
hours and minutes.
7
or ∞ when you reach the correct setting.
3 Release
4 After you have set both the hour and minutes, turn the clock control to
CLOCK to run on clock time.
SELECTING THE ALARM MODE
GENERAL
If you wish to use the alarm, you must first set the alarm time first. You can
choose from two different alarm modes to wake you up: by radio or buzzer.
• Select your choice of alarm mode by adjusting ALARM 1 or ALARM 2 to RAD
or BUZ.
™ The 2 buzzers are at a set volume and cannot be adjusted. BUZ on
ALARM 1 is a low tone buzzer while BUZ on ALARM 2 is a high tone.
MAINTENANCE
• If you do not intend to use the set for a long time, withdraw the mains plug
from the wall socket. In addition to this, it is advisable to remove the battery
from the clock radio. This will prevent any danger of leakage and the clock
radio will not be damaged.
• Do not expose the set to humidity, rain, sand or excessive heat caused by
3
heating equipment or direct sunlight.
• To clean the set, use a soft, slightly dampened chamois leather. Do not use
any cleaning agents containing alcohol, ammonia, benzene or abrasives as
4
these may harm the housing.
ENVIRONMENTAL INFORMATION
5
We have reduced packaging to the minimum for easy separation into two
6
materials: paper and cardboard.
Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe local regulations on the disposal of packing
7
materials and old equipment.
This product complies with the radio interference requirements of the
English
to ON to switch on the radio.
to OFF to switch off the radio.
7
or ∞ buttons separately and not simultaneously.
European Union.
INSTALLATION
POWER SUPPLY
1 Check if the mains supply, as shown on the type plate
bottom of the set, corresponds to your local mains su
consult your dealer or service centre.
2 Connect the mains lead to the wall socket.
3 To disconnect the set from the mains supply completel
the wall socket.
CLOCK MEMORY BACKUP
The clock memory backup allows your alarm and clock tim
for up to a day when there is a power interruption e.g. ma
plete clock radio and display illumination will be switched
mains supply returns, the display will indicate the correct
1 Remove the battery door to insert a 9 volt 6F22 type b
backup.
2 Replace the battery door.
NOTE: If no backup battery is installed or the power interr
will need to set the clock and alarm times again.
Batteries contain chemical substances so sho
properly.
Standby power consumption . . . . . . . . . . . . . . . . . . . . . .
For users in the U.K.: please follow the instructions
sheet.
SWITCHING OFF THE ALARM
There are three ways of switching off the alarm. Unless y
completely, the 24 hour alarm reset option will be auto
59 minutes, from the time your alarm time first goes off.
24 HOUR ALARM RESET
If you want the alarm mode to be stopped immediately bu
same alarm setting for the following day:
• Press ALARM RESET during the alarm call.
CANCELING THE ALARM COMPLETELY
To cancel the set alarm time before it goes off, or during t
• Adjust ALARM 1 or ALARM 2 to OFF position.
REPEAT ALARM
This repeats your alarm call at 6-7-minute intervals.
1 During the alarm call, press
/REPEAT ALARM.
SLEEP OFF
2 Repeat if desired for up to 59 minutes.
SLEEP
About Sleep
This set has a built-in timer which enables the set to be a
off during radio playback after a set period of time. This a
listen and fall asleep. The maximum sleep time is 59 minu
Setting SLEEP
1 Check that the clock control is in CLOCK position.
2 Set RADIO to OFF position.
3 Set your sleep time by pressing on the SLEEP button.
button and the display will begin to count down from 0
™ To cancel sleep, or to switch off the sleep period pr
/REPEAT ALARM.
SLEEP OFF
TROUBLESHOOTING
If a fault occurs, first check the points listed below before tak
If you are unable to remedy a problem by following these hint
service centre.
WARNING: Under no circumstances should you try to repair
will invalidate the guarantee. Do not open the se
electric shock.
Problem
– Possible Cause
• Remedy
No sound/power
– Volume not adjusted
• Adjust the volume
Occasional crackling sound during FM broadcast
– Weak signal
• Extend and position the pigtail
Continuous crackling/hiss disturbance during MW (
– Electrical interference from TV, computer, fluorescent lamp
• Move set away from other electrical equipment
The alarm does not function