Eaton PowerXL DG1 Serie Instrucciones De Montaje página 22

Instruction Leaflet IL040016EN
Effective January 2022
Factory-set control terminal functions
I/O connection
External wiring Pin Signal name
1 +10 V
2 AI1+
1
3 AI1–
4 AI2+
1
i
5 AI2–
6 GND
7 DIN5
8 DIN6
9 DIN7
10 DIN8
11 CMB
12 GND
13 24 V
14 DO1
15 24 Vo
16 GND
17 AO1+
18 AO2+
19 24 Vi
20 DIN1
21 DIN2
22 DIN3
23 DIN4
24 CMA
25 A
26 B
27 R3NO
28 R1NC
29 R1CM
30 R1NO
31 R3CM
32 R2NC
33 R2CM
34 R2NO
The above wiring demonstrates a SINK configuration. It is important that CMA and CMB are wired to ground (as shown by dashed line).
If a SOURCE configuration is desired, wire 24 V to CMA and CMB and close the inputs to ground. When using the +10 V for AI1, it is
important to wire AI1—to ground (as shown by dashed line). If using +10 V for AI1 or AI2, terminals 3, 5, and 6 need to be jumpered together.
1
AI1+ and AI2+ support 10K potentiometer.
22 EATON www.eaton.com
Signal Default setting
Ref. Output Voltage —
Analog Input 1 0–10 V
Analog Input 1 Ground —
Analog Input 2 4 mA to 20 mA
Analog Input 2 Ground —
I/O Signal Ground —
Digital Input 5 Preset Speed B0
Digital Input 6 Preset Speed B1
Digital Input 7 Emergency Stop (TI–)
Digital Input 8 Force Remote (TI+)
DI5 to DI8 Common Grounded
I/O Signal Ground —
+24 Vdc Output —
Digital Output 1 Ready
+24 Vdc Output —
I/O Signal Ground —
Analog Output 1 Output Frequency
Analog Output 2 Motor Current
+24 Vdc Input —
Digital Input 1 Run Forward
Digital Input 2 Run Reverse
Digital Input 3 External Fault
Digital Input 4 Fault Reset
DI1 to DI4 Common Grounded
RS-485 Signal A —
RS-485 Signal B —
Relay 3 Normally Open At Speed
Relay 1 Normally Closed Run
Relay 1 Common
Relay 1 Normally Open
Relay 3 Common At Speed
Relay 2 Normally Closed Fault
Relay 2 Common
Relay 2 Normally Open
PowerXL DG1 Series VFD
Description
10 Vdc Supply Source
Voltage Speed Reference (Programmable to 4 mA to 20 mA)
Analog Input 1 Common (Ground)
Current Speed Reference (Programmable to 0–10 V)
Analog Input 2 Common (Ground)
I/O Ground for Reference and Control
Sets frequency output to Preset Speed 1
Sets frequency output to Preset Speed 2
Input forces VFD output to shut off
Input takes VFD from Local to Remote
Allows source input
I/O Ground for Reference and Control
Control voltage output (100 mA max.)
Shows the drive is ready to run
Control voltage output (100 mA max.)
I/O Ground for Reference and Control
Shows Output frequency to motor 0–60 Hz (4 mA to 20 mA)
Shows Motor current of motor 0–FLA (4 mA to 20 mA)
External control voltage input
Input starts drive in forward direction (start enable)
Input starts drive in reverse direction (start enable)
Input causes drive to fault
Input resets active faults
Allows source input
Fieldbus Communication (Modbus, BACnet)
Fieldbus Communication (Modbus, BACnet)
Relay output 3 shows VFD is at Ref. Frequency
Relay output 1 shows VFD is in a run state
Relay output 3 shows VFD is at Ref. Frequency
Relay output 2 shows VFD is in a fault state