Ryobi LLCDI1802 Manual De Utilización página 7

GB
FR DE ES IT
OPERATION
WARNING
Do not allow familiarity with products to make you
careless. Remember that a careless fr action of a
second is sufficient to inflict serious injury.
WARNING
Always w ear saf ety goggles or saf ety glasses
with side shields when operating products. Failure
to do so could result in objects being thro
your eyes, resulting in possible serious injury.
WARNING
Do not use an y attachments or accessor ies
not recommended b y the man ufacturer of this
product. The use of attachments or accessor
not recommended can result in ser ious personal
injury.
APPLICATIONS
You may use this product for the purposes listed below:
Drilling in all types of wood products (lumber, plywood,
■
panelling, composition board, and hard board)
Drilling in ceramics, plastics, fiberglass, and laminates
■
Drilling in metals
■
Driving screws
■
Hammer drilling in concrete, brick, or other masonry
■
This product will accept R YOBI One+ 18 V lithium-ion
battery pac ks and R YOBI One+ 18 V nic kel-cadmium
battery packs.
BATTERY PROTECTION FEATURES
RYOBI 18 V lithium-ion batter ies are designed with
features that protect the lithium-ion cells and maximiz
battery lif e. Under some oper ating conditions , these
built-in features may cause the batter y and the tool it is
powering to act differently from nickel-cadmium batteries.
During some applications , the batter y electronics ma y
signal the batter y to shut do wn, and cause the tool to
stop r unning. To reset the batter y and tool, release the
trigger and resume normal operation.
NOTE: To prevent fur ther shut do wn of the batter y, avoid
forcing the tool.
If releasing the tr igger does not reset the batter
tool, the batter y pack is depleted. If depleted, the batter y
pack will begin charging when placed on the lithium-ion
charger.
TO INSTALL BATTERY PACK
See Figure 2.
Lock the switch trigger by placing the rotation selector
■
in the center position.
Place the battery pack on the tool.
■
All manuals and user guides at all-guides.com
NL PT DK SE FI NO
English
wn into
ies
e
y and
RU PL CZ HU RO LV
Make sure the latches on each side of the batter
■
pack snap into place and the batter
on the tool before beginning operation.
WARNING
Always remove battery pack from your tool when
you are assemb ling par ts, making adjustments ,
cleaning, or when not in use . Remo ving batter y
pack will pre vent accidental star
cause serious personal injury.
TO REMOVE BATTERY PACK
See Figure 2.
Lock the switch trigger by placing the rotation selector
■
in the center position.
Depress the latches on the side of battery pack.
■
Remove the battery pack from the tool.
■
WARNING
Battery tools are alw ays in oper ating condition.
Therefore, switch should alw ays be loc ked when
not in use or carrying at your side.
SWITCH TRIGGER
See Figure 3.
To turn the drill ON, depress the switch trigger.
■
To turn it OFF, release the switch trigger.
■
VARIABLE SPEED
The v ariable speed s witch tr igger deliv ers higher speed
and torque with increased tr igger pressure and lo wer
speed with decreased trigger pressure.
NOTE: You might hear a whistling or r
the s witch dur ing use . Do not be concer
normal part of the switch function.
ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK)
See Figure 3.
The bit rotation is re versible and is controlled b
selector located abo ve the s witch tr igger. With the dr ill
held in nor mal oper ating position, the rotation selector
should be positioned to the left of the s
forward drilling. The drilling direction is reversed when the
selector is to the right of the switch trigger.
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental star
not in use.
CAUTION:
To prevent gear damage , always allow the chuck
to come to a complete stop bef
direction of rotation.
To stop the dr ill, release the s witch tr igger and allo w the
chuck to come to a complete stop.
2
LT EE HR SI SK GR
y pack is secured
ting that could
inging noise from
ned; this is a
y a
witch tr igger f or
ting when
ore changing the
TR
y