Maintenance; Parts List - Sagola MACK 400 Manual De Instrucciones, Lista De Repuestos

5.- Pull the spray gun trigger, holding it until the sprayed
product is clean thinner and free from the product previously
applied.
It is considered that the unit and its accessories are
totally clean when the product sprayed through the gun,
and that circulating through the product return probe
No. 2, is clean thinner and free from the product
previously applied, meaning that the process must be
repeated as many times as necessary.
Once the unit and its accessories are clean, and as a
prior step before definitively stopping it, the
Depressurisation procedure described before in Section
10 of the Manual must be applied.
Clean the Suction Probe filters (No.8), anti-pulsations filter
(No.10) and the spray gun filters.
Remove any remains of product from the gun, hoses and
the rest of the unit with a cloth soaked in thinner.
Keep gasket areas free of accretions and foreign bodies.
The air cap is a precision component. Any deformation,
especially in the product outlet orifices, may cause malfunctions
in its operation and incorrect or deficient quality spraying.
Before starting to work, verify the state of the product hoses and
the connections of the elements through which the product flows.
CHECK AND FILL EVERYDAY WITH THE LUBRICANT
SAGOLA 30090098, IF NECESSARY, THE EXISTING
ACCOMMODATION IN THE GLAND (9). REPLACE IF DIRTY
OR DAMAGED.
In order to carry out maintenance or repairs, first disconnect the
unit from the compressed air distribution network.
Never move the unit by tugging on the hoses.
Always place the unit at a distance of least 6 metres away from
where the product is to be applied.
06
09
05
20
21
04
23
03
27
02
25
25
22
22
19
26
18
11
24
14
15
01
1 Mack400
10
16
2 Mack600
17
1 Mack400
12
2 Mack600
95
91
page 9

14. MAINTENANCE

15. PARTS LIST

43
43
37 53
51
36 45
38
35
40
52
58
08
82 07
82
85
83
89
90
88
47
87
84
55
39
86
57
13
45
92
50
47
46
93 94
If necessary, dip the air cap in thinner in order to soften the
remains of product or dirt. Once softened, blow the cap with
compressed air until any remains of product and thinner are
eliminated.
For automatic cleaning of the gun, tools and accessories
used in the mixing and preparation of the product to be
applied, we recommend the use of SAGOLA Washing
Machines.
IMPORTANT
The gun can be cleaned with thinners or detergents in
a gun washing machine.
If you opt for this cleaning system, we advise you to
remember the following considerations, which, if not applied,
may damage the gun and render the warranty null and void.
- Do not submerge the gun in solvent or detergents longer
than the time required for cleaning.
- Do not use the gun immediately after cleaning has been
completed.
- Ensure that there is no thinner or detergent inside and that
it is completely free of these. Other cleaning systems can
be used (ultrasound).
Do not apply excessive force or inadequate tools for maintaining
and cleaning the unit. Some repairs must be done with special
tools on some occasions. In these cases, you must contact the
Customer Service of SAGOLA. Any handling of this product by
non-authorised personnel would render the warranty null and
void.
The unit must be overhauled on a periodic basis to check the
status of its components and replace these when they are not
in perfect condition.
IN ORDER TO OBTAIN THE BEST POSSIBLE RESULTS,
ALWAYS USE ORIGINAL SAGOLA SPARES THAT
GUARANTEE TOTAL INTERCHANGEABILITY, SAFETY AND
PERFECT OPERATION.
47
49
60
29
42
41
32
30
56
41
33
64
34
65
42
28
56
31
61
59
62
52
48
35
38
40
44
54
66
page 10
- 20 -
12/1 12/2
70/1
71/1 71/2
76
80/1
81/1 81/2
79/1
72/1 72/2
69 69
78/1
72/1
73
75/1
10/1
67/1 67/2
74 74
77
68
page 11
70/2
76
80/2
79/2
78/2
72/2
73
75/2
10/2
77
68