Specific Safety Rules - Makita 6940D Manual De Instrucciones

Ocultar thumbs Ver también para 6940D:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 15
ENGLISH
1
Battery cartridge
2
Set plate
3
Insert bit
4
Spindle
5
Hex bolt
6
Angle head
SPECIFICATIONS
Model
Capacities
Bolt ...........................................................................................M4 – M10
Machine screw ..........................................................................M4 – M8
-1
No load speed (min
) ..................................................................0 – 2,000
Impacts per minute ......................................................................0 – 2,700
Fastening torque ..........................................................................29 N.m
Overall length ..............................................................................370 mm
Net weight ....................................................................................1.5 kg
Rated voltage ..............................................................................D.C. 9.6 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended Use
The tool is intended for drilling and screw driving in wood,
metal and plastic.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1.
Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using battery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6.
Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
Explanation of general view
7
Groove
8
Tooth
9
Reversing switch
10 Switch lever
11 Position R
(Counterclockwise rotation)
(with Angle head)
7.
8.
9.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
ENC004-1
2.
3.
4.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained
adherence to impact driver safety rules. If you
use this tool unsafely or incorrectly, you can
suffer serious personal injury.
1.
2.
3.
4.
12 Position F
(Clockwise rotation)
13 Release button
14 Straight head
15 Ratchet head
6940D
(with Straight head)
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
from
repeated
Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
Hold the tool firmly.
Wear ear protectors.
6941D
M4 – M10
M4 – M8
0 – 2,000
0 – 2,700
39 N.m
360 mm
1.4 kg
D.C. 9.6 V
GEB012-2
use)
replace
strict
3

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

6941d

Tabla de contenido