Symbols On The Machine - Metabo PowerAir V400 Manual De Instrucciones Original

ENGLISH
was designed for (see Technical
Specifications).
B
Danger! Risk of electric
shock!
• Do not expose electric tool to rain.
• Do not operate electric tool in damp
or wet environment.
Prevent body contact with earthed
•
objects such as radiators, pipes,
cooking stoves or refrigerators
when operating this electric tool.
• Do not use the power cable for pur-
poses it is not intended for.
A
Risk of personal injury by es-
caping compressed air and parts
hurled about by escaping air!
• Never direct compressed air against
persons or animals!
Ensure all air tools and accessories
•
used are designed for the working
pressure or are supplied via a pres-
sure regulator.
Please note that, when disconnect-
•
ing the quick coupler, the com-
pressed air contained in the pres-
sure hose will escape all of a
sudden. You should therefore firmly
hold the air hose when disconnect-
ing it.
• Ensure all screwed connections are
fully tightened at all times.
• Do not attempt to repair the ma-
chine yourself! Only trained special-
ists are permitted to service or re-
pair compressors, pressure vessels
and air tools.
A
Hazard generated by lubricat-
ed compressed air!
• Use lubricated compressed air only
for air tools requiring such supply.
Do not use an air hose used to sup-
•
ply compressed air containing oil to
supply air tools not designed for op-
eration on compressed air contain-
ing oil.
• Do not fill tyres with lubricated com-
pressed air.
A
Risk of burns from the surfac-
es of parts carrying compressed air!
• Let tool cool off before servicing.
12
A
Risk of personal injury and
crushing by moving parts!
• Do not operate the electric tool with-
out installed guards.
• Please note that the compressor will
start automatically when the pres-
sure falls off to minimum! – discon-
nect from power supply prior to any
servicing.
• Ensure that when switching on (e.g.
after servicing) no tools or loose
parts are in the electric tool.
A
Hazard generated by insuffi-
cient personal protection gear!
• Wear hearing protection.
• Wear safety goggles.
• Wear mask respirator when work
generates dust or mist detrimental
to health.
• Wear suitable work clothes. When
working outdoors wearing of non-
slip shoes is recommended.
B
Hazard generated by electric
tool defects!
• Keep electric tool and accessories
in good repair. Observe the mainte-
nance instructions.
• Prior to any use check the electric
tool for possible damage: before op-
erating the electric tool all safety de-
vices, protective guards or slightly
damaged parts need to be checked
for proper function as specified.
• Check to see that all moving parts
work properly and do not jam. All
parts must be correctly installed and
meet all conditions necessary for
the proper operation of the electric
tool.
• Damaged protection devices or
parts must be repaired or replaced
by a qualified specialist.
Have damaged switches replaced
•
by a Service Centre.
• Do not operate electric tool if the
switch can not be turned ON or
OFF.
• Keep handles free of oil and grease.
3.3

Symbols on the machine

Symbols on the machine
16 17 18 19
16 Read instructions.
17 Warning that personal injury may
occur through touching of hot
parts.
18 Wear safety goggles.
19 Warning against automatic star-
tup.
20 Warning against dangerous volt-
age.
21 Guaranteed sound power level.
Information on nameplate:
22
23
24
25
26
27
28
29
30
37
22 Manufacturer
23 Article number, version number,
serial number
24 Machine designation
25 Supply voltage / Frequency
26 Motor capacity P (see also
1
„Technical Specifications")
27 Power consumption / Protection
rating
28 Motor speed
29 CE-mark – This machine con-
forms to the EC Directives as per
Declaration of Conformity
30 Date of manufacture
31 Suction capacity
32 Filling rate
33 Speed (compressor pump)
34 No. of cylinders
20
21
31
32
33
34
35
36