Makita DFT085F Manual De Instrucciones página 7

Ocultar thumbs Ver también para DFT085F:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 37
Reversing switch action
► Fig.5: 1. Reversing switch lever
CAUTION:
Always check the direction of
rotation before operation.
CAUTION:
Use the reversing switch only after
the tool comes to a complete stop. Changing the direc-
tion of rotation before the tool stops may damage the tool.
CAUTION:
When not operating the tool, always
set the reversing switch lever to the neutral position.
Function
Auto-stop with fastening
completion
Alarm against insuffi-
cient fastening
Alarm for low battery
capacity
Auto-stop with low
remaining battery
capacity
Check of the LED indi-
cator, light and beeper
operation
Anti-reset of controller
Overheat protection
Detection of switch
trigger operation when
installing battery
Motor failure detection
Double-hitting detection
Maintenance alarm
Alarm for unavailable
data communication
(with the tool in connec-
tion with PC)
Indication that data com-
munication is available
(with the tool in connec-
tion with PC)
Status of the tool
The preset fasten-
Lights up in green for
ing torque has been
approximately one
achieved and the tool
second.
has stopped.
The preset fastening
Lights up in red.
torque has not been
achieved, because
the switch trigger has
released before complet-
ing the fastening.
The battery power
Flickers in red slowly.
became low and it is
time to replace the
battery cartridge.
The battery power is
Lights up in red.
almost used up and the
tool stopped.
When the battery
Lights up first in green,
cartridge is installed,
next red.
the tool checks for its
(And then the light
LED indicator, light and
comes on.)
beeper.
The battery voltage
Flickers in red and green
dropped abnormally for
alternatively.
some reason, and the
tool stopped.
Tool's controller heated
Flickers in red quickly.
up abnormaly and the
tool stopped.
When the battery car-
Flickers in red and green
tridge is installed with
alternatively.
the switch trigger pulled,
the tool stops to avoid
unintentional start.
Motor failure has been
Flickers in red and green
detected. At this time,
alternatively.
tool does not work.
When the operator
Lights up in red.
starts to re-fasten an
already-fastened screw,
the tool detect it and stops.
A maintenance time has
Flickers in yellow.
come according to your
preset number of screws
driven.
Data cannot be
Flickers in yellow.
exchanged between the
tool and PC in spite of
the connection.
The tool is connected to
Flickers in green.
PC and data communi-
cation is available.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
LED indicator / Beeper
► Fig.6: 1. LED indicator
LED indicator / Beeper on the tool shows the following
functions.
Status of the LED indicator/beeper
LED indicator
A long beep
A series of long beeps
A long beep
A series of very short
beeps
A series of short beeps
A series of short beeps
A series of short beeps
A series of short beeps
A long beep
7 ENGLISH
Action to be taken
Beeper
Retighten the screw.
Replace the battery with
fully charged one.
Replace the battery with
fully charged one.
Replace the battery with
fully charged one.
Remove the battery car-
tridge immediately and
cool the tool down.
Release the switch
trigger.
Ask your local Makita
Service Center for repair.
Reset the alarm with the
application software.
Restart the application
software and re-connect
the USB cable.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Dft127f

Tabla de contenido