Tripp-Lite SmartOnline 8kVA Manual Del Propietário página 4

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Mounting (Tower)
Mount all modules in an upright, tower position using included base stands. The user must determine the fitness of hardware and procedures before
mounting.
The UPS system is shipped with two sets of plastic feet
1
to tower mount the UPS's power module, a battery module and a second battery module (9U
total).
Adjust the feet to a width of 10.25 inches (26 cm) for a UPS power module and battery module,
or to a width of 15.375 inches (39 cm) for three units. Align the feet in your installation area,
approximately 10 inches (26 cm) apart. Have one or more assistants help you place the units on
their sides in the feet. The control panel of the UPS should be the UPS's upper corner and face
outward.
Rotate the power module's Control Panel to view it easier while the UPS is tower mounted.
2
Insert a small screwdriver, or other tool, in the slots on either side of the Control Panel. Pop the
panel out; rotate it; and pop the panel back into place.
Features
Before installing and operating your UPS, familiarize yourself with the location and function of the features of each component.
Power Module Front Panel Controls
LCD DISPLAY: This backlit (16 × 2 character) dot matrix display indicates a wide range of
1
UPS operating conditions and diagnostic data. It also displays UPS settings and options when
the UPS is in setup mode.
ON/MUTE BUTTON: Press this button and hold it until you hear a beep to turn the UPS
2
system's inverter ON. If the UPS's battery alarm is sounding, press this button to silence it.
SCROLL DOWN/EXIT SETUP BUTTON: This button allows you to browse through
3
different options and power readings on the LCD display. Momentarily pressing it causes the
LCD screen to display a different power reading (see "Operation", pg. 12). Pressing it and the
SCROLL UP Button together puts the UPS in setup mode, where this button is used to scroll
through setup options and to exit setup mode.
SCROLL UP/SELECT BUTTON: This button allows you to browse through different
4
options and power readings on the LCD display. Momentarily pressing it causes the LCD
screen to display a different power reading (see "Operation Section", pg. 17). Pressing it and
the SCROLL DOWN Button together puts the UPS in setup mode, where this button is used
to select setup options.
OFF BUTTON: Press this button until you hear a beep to turn the UPS system's inverter
5
OFF.
O/P (OUTPUT) LED: This green light will illuminate to indicate your UPS is supplying AC
6
power to connected equipment.
DC/AC (INVERTER) LED: This green light will illuminate to indicate the UPS's DC/AC inverter is activated.
7
BYPASS LED: This green light will illuminate when the UPS is providing filtered mains power without engaging its converter or inverter. If
8
this LED is lit, connected equipment will not receive battery power in the event of a blackout, unless the Economy Mode feature is enabled.
AC/DC (Converter) LED: This green light will illuminate to indicate the UPS's AC/DC converter is charging the connected battery pack(s).
9
BATTERY LED: This green light will illuminate when the UPS is discharging the battery to provide connected equipment with AC power. An
10
alarm will sound which can be silenced by pressing the ON/MUTE Button. This LED will remain lit after the alarm is silenced.
I/P (INPUT) LED: This green light will illuminate to indicate an AC input supply is present.
11
ACCESS SLOTS: To rotate the controls, insert a flathead screwdriver into these slots and gently lever the panel out. Taking care not to
12
excessively twist or yank the cables connecting the controls to the rest of the UPS, turn the controls to the desired orientation and reinsert them.
201102160 93-2897.indb 4
and extensions
that can be used
A
B
4
A
1
2
12
11
10
9
8
7
6
1
2
3
4
B
12
5
3/30/2011 9:30:40 AM

Publicidad

Tabla de contenido
loading

Tabla de contenido