Stanley FATMAX SFMCD710 Traducido De Las Instrucciones Originales página 10

ENGLISH
Drilling in metal
Use a cutting lubricant when drilling metals. The exceptions
are cast iron and brass which should be drilled dry. The cutting
lubricants that work best are sulphurized cutting oil.
LED work light (Fig H)
When drill is activated by pulling the trigger switch (1), the
integrated LED work light (7) will automatically illuminate the
work area.
Note: The work light is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Troubleshooting
Problem Possible cause
Unit will not start. Battery pack not
installed properly.
Battery pack
not charged.
Unit starts The switch has
immediately upon been left in the
inserting battery "on" position.
Battery pack will Battery pack not
not charge. nserted into charger.
Charger not
plugged in.
Surrounding air
temperature too hot or
too cold.
Unit shuts off abruptly. Battery pack has
reached its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery pack it is
designed to shutoff
abruptly when the
charge is depleted
Maintenance
Your STANLEY FATMAX tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
u
Do not use any abrasive or solvent-based cleaner.
u
10
(Original instructions)
Possible solution
Check battery
pack installation.
Check battery pack
charging requirements.
The switch must be moved
to "off" to prevent the tool
from immediately starting
when battery is inserted.
Insert battery pack into
charger until LED lights.
Plug charger into a
working outlet.
Move charger and battery
pack to a surrounding
air temperature of above
45 °C or below +40.5 °C.
Allow battery pack to cool
down.
Place on charger and allow
to charge.
Protecting the environment
Z
Separate collection. Products and batteries marked
with this symbol must not be disposed of with
normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com
Technical data
Voltage
No-load speed
Max. torque
Chuck capacity
Max Drilling capacity
Steel/wood
Weight
Charger SFMCB11
Input Voltage
V
AC
Output Voltage
V
DC
Current A
Battery SFMCB201
Voltage 18
V
DC
Capacity Ah 1.5
Type
Li-Ion
Level of sound pressure according to EN60745:
Sound pressure (L ) 74.0 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L ) 85.0 dB(A), uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN60745:
2
Drilling into metal (a ) 1.7 m/s , uncertainty (K) 1.5 m/s
h, D
SFMCD710
V
DC
0-600 / 0-1900RPM
-1
Min
Nm
mm
mm
kg 1.2 (without battery)
SFMCB12 SFMCB14
230 230
18 18
1.25 2
SFMCB202 SFMCB204 SFMCB206
18 18
2.0 4.0
Li-Ion Li-Ion
2
18V
60
1.5-13
13/30
230
18
4
18
6.0
Li-Ion