Switch 6: Programming Of Opening Position Of Adjustable Louver Blades - V2 LEX-RFO40-230V Manual Del Usuario

SWITCH 4: PROGRAMMING OF OPENING
LIMIT SWITCH OF THE ROLLING SHUTTER
To set the opening limit switch on a rolling shutter with
a blockage at the top, you must have a previously stored
remote control available and must proceed with the
following points.
1. Power only the control unit to be programmed
2. Multichannel transmiter only: press several times the key SELC
of the transmitter until displayed the channel stored
3. Take the roll-up shutter to half its way by the keys UP or
DOWN
4. Set to ON the switch 4 of the transmitter
5. Press and keep pressed - for about 5 seconds - the key PROG
of the transmitter until the motor, moving for 1/2 second in
both the ways, proves it is entering into programming phase.
6. Release the key PROG
7. Press the key UP: the roll-up shutter goes up at normal speed
8. Once in contact with the upper lock, it stops and memorizes
the position
9. Set to OFF the switch 4 of the transmitter
To set the opening limit switch on a rolling shutter without
blockage at the top, you must have a previously stored
remote control available and must proceed with the
following points.
1. Power only the control unit to be programmed
2. Multichannel transmiter only: press several times the key SELC
of the transmitter until displayed the channel stored
3. Position the roll-up shutter at the mid-height
4. Set to ON the switch 4 of the transmitter
5. Press and keep pressed - for about 5 seconds - the key PROG
of the transmitter until the motor, moving for 1/2 second in
both the ways, proves it is entering into programming phase
6. Release the key PROG
7. Position the roll-up shutter in the UPPER position desired using
the UP and DOWN buttons. To regulate it precisely, press the
PROG button when the motor is close to the limit switch. the
motor will start to move in jerks
8. Press the key STOP once reached the required position: the
motor stops and proves the correct storage of the
end-of-stroke with a 1/2 second movement first downwards
and then upwards.
9. Set to OFF the switch 4 of the transmitter
SWITCH 5: PROGRAMMING OF CLOSING
LIMIT SWITCH OF ROLLING SHUTTER
(LOUVER BLADES)
NOTE: you must have a previously stored remote control
available and must proceed with the following points.
1. Multichannel transmiter only: press several times the key SELC
of the transmitter until displayed the channel stored
2. Position the roll-up shutter at the mid-height
3. Set to ON the switch 5 of the transmitter
4. Press and keep pressed - for about 5 seconds - the key PROG
of the transmitter until the motor proves it is entering into
programming phase by moving for 1/2 second in both the
ways
5. Release the key PROG
6. Position the roll-up shutter in the LOWER position desired
using the UP and DOWN buttons. To regulate it precisely, press
the PROG button when the motor is close to the limit switch:
the motor will start to move in jerks
7. Press the key STOP once reached the required position: the
motor stops and then proves the correct storage of the
end-of-stroke by moving for 1/2 second first upwards and
then downwards
8. Set to OFF the switch 5 of the transmitter
SWITCH 6: PROGRAMMING OF OPENING
POSITION OF ADJUSTABLE LOUVER BLADES
NOTE: you must have a previously stored remote control
available and must proceed with the following points.
1. Multichannel transmiter only: press several times the key SELC
of the transmitter until displayed the channel stored
2. Take the roll-up shutter to the desired position with the keys
UP, DOWN and STOP
3. Set to ON the switch 6 of the transmitter
4. Press and keep pressed - for about 5 seconds - the key PROG
of the transmitter until the motor proves the correct storage of
the end-of-stroke by moving for 1/2 second in both the ways
5. Release the key PROG
6. Using the UP and DOWN buttons, open the louver blades to
he desired position. To perform a precise adjustment press
the PROG button when the motor approaches the desired
position, the motor will begin to move jerkily
7. Press the key STOP once reached the required position: the
motor stops and then proves the correct storage of the
end-of-stroke by moving for 1/2 second first upwards and
then downwards
8. Set to OFF the switch 6 of the transmitter
To bring the rolling shutter into the opening position of the
adjustable louver blades press the STOP button for at least
3 seconds (with the motor stationary): the louver blades
moves until it reaches the tracked position.
- 18 -