Safety Warnings Specifi c for Sanding Operations:
a) Do not use excessively oversized sanding disc paper.
Follow manufacturers recommendations, when selecting
sanding paper. Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and may cause
snagging, tearing of the disc or kickback.
Safety Warnings Specifi c for Wire Brushing Operations:
a) Be aware that wire bristles are thrown by the brush even
during ordinary operation. Do not overstress the wires by
applying excessive load to the brush. The wire bristles can
easily penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or brush
with the guard. Wire wheel or brush may expand in diameter
due to work load and centrifugal forces.
Additional Safety and Working Instructions
When grinding metal, fl ying sparks are produced. Take care
that no persons are endangered. Because of the danger of fi re,
no combustible materials should be located in the vicinity
(spark fl ight zone). Do not use dust extraction.
Avoid fl ying sparks and sanding dust hit your body.
Never reach into the danger area of the machine when it is
running.
Immediately switch off the machine in case of considerable
vibrations or if other malfunctions occur. Check the machine in
order to fi nd out the cause.
Under extreme conditions (e.g. smooth-grinding metals with the
arbour and vulcanized fi bre grinding disk), signifi cant
contamination can build up on the inside of the angle grinder
(metal residue/deposits). For safety reasons, in such conditions
a ground fault interrupter must be connected in series. If the
ground fault interrupter trips the machine must be sent for
service.
Sawdust and splinters must not be removed while the machine
is running.
MAINS CONNECTION
Connect only to single-phase AC current and only to the
system voltage indicated on the rating plate. It is also possible
to connect to sockets without an earthing contact as the design
conforms to safety class II.
Appliances used at many different locations including wet room
and open air must be connected via a residual current device
(FI, RCD, PRCD) of 30mA or less.
Only plug-in when machine is switched off.
Do not let any metal parts reach the airing slots - danger of
short circuit!
Inrush currents cause short-time voltage drops. Under
unfavourable power supply conditions, other equipment may be
affected. If the system impedance of the power supply is lower
than 0,2 Ohm, disturbances are unlikely to occur.
SPECIFIED CONDITIONS OF USE
The angle grinder is intended for grinding and cutting metal,
stone and ceramic materials as well as sanding and wire
brushing.
Use the safety guard from the accessories range when
performing out cutting work.
Please refer to the instructions supplied by the accessory
manufacturer
The machine is suitable only for working without water.
WORKING INSTRUCTIONS
For accessories intended to be fi tted with threaded hole wheel,
ensure that the thread in the wheel is long enough to accept
the spindle length.
Always use and store the cutting and grinding disks according
to the manufacturer's instructions.
22
ENGLISH
Always use the correct guard for cutting and grinding.
Always use guard with cutting guide from the accessories
range for cutting stone.
The grinding surface of the centre depressed wheels must be
mounted min. 2 mm below the plane of the guard lip.
The adjusting nut must be tightened before starting to work with
the machine.
Always use the auxiliary handle.
The workpiece must be fi xed if it is not heavy enough to be
steady. Never move the workpiece towards the rotating disk by
hand.
STARTUP PROTECTION
Machines with a lockable switch are supplied with a restart
cutout. This prevents the machine restarting by itself after a
power failure. When resuming work, switch the machine off and
then switch it back on again.
STARTING CURRENT LIMITER + SMOOTH START
The starting current for the machine is several times greater
than rated current. The starting current limiter reduces the
starting current to such an extent that a fuse (16 A, slow-blow)
is not tripped.
Electronic smooth start for save use prevents jerky run-up of
the machine.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
If the supply cord of this power tool is damaged, it must be
replaced by a specially prepared cord available through the
service organization.
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the Article No. as well as the machine type printed on the
label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
provisions of the directives 2011/65/EU (RoHs), 2004/108/EC
(until 19 April 2016), 2014/30/EU (from 20 April 2016), 2006/42/
EC and the following harmonized standards have been used:
EN 60745-1:2009+A11:2010
EN 60745-2-3:2011+A2:2013+A11:2014+A12:2014+A13:2015
EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997+A1:2001+A2:2008
EN 61000-3-2:2014
EN 61000-3-3:2013
EN 50581:2012
Winnenden, 2016-02-04
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
SYMBOLS
CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket
before carrying out any work on the machine.
Please read the instructions carefully before starting
the machine.
Always wear goggles when using the machine.
Wear gloves!
Do not use force.
Only for grinding.
Only for cutting work.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that
have reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
Class II tool, tool in which protection against
electric shock does not rely on basic insulation
only, but in which additional safety precautions,
such as double insulation or reinforced
insulation, are provided.
There being no provision for protective earthing
or reliance upon installation conditions.
European Conformity Mark
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
National mark of conformity Ukraine
EurAsian Conformity Mark.
ENGLISH
23