Publicidad
Idiomas disponibles
Idiomas disponibles
Programming the push-buttons
The video-interphone is supplied with 3 push-buttons for the following
functions: lock release, self-start and "stair light" auxiliary service, which
activates the 1st relay of the 1st actuator (type 69HR), if connected to
the installation and with other 6 push-buttons for intercommunicating
calls or auxiliary services.
To change the operation type of push-buttons it is necessary to use pro-
grammer type 950C or SaveProg, with the exception of the assignation
of the functions for the intercommunicating calls and self-start to a spe-
cific entrance panel.
Programming the push-buttons for the intercommunicating calls
(With series 8870, Giotto, Petrarca raise the handset of the inter-
phone / video-interphone to call. On the 6600 series keep pressed
the talk / listen push-button "I").
Programming phase:
1)
Press and hold down "I".
2)
Press and hold down also "H" together with "I".
3)
Wait for nearly 3 seconds until the red led "M" flashes.
4)
Now the microprocessor is physically reset.
5)
Release both push-buttons "I" and "H"
6)
Press and hold down the "F" push-button to be programmed.
7)
After 2 seconds the video-interphone emits a high-pitched tone,
while the other interphone / video-interphone emits a three-tone
ascending scale.
8)
Release the "F" push-button related to the intercommunicating call.
9)
On the called interphone / video-interphone (the one with the three-
tone scale) press one of the push-buttons programmed as door lock
or F1 or F2 or the auxiliary one.
10) A high-pitched tone confirms the end of the procedure.
Repeat the procedure also for the other interphones / video-inter-
phones ad possible intercommunicating call push-buttons.
Programming the self-start push-button to a specific entrance panel.
Programming phase:
1)
Press and hold down "I".
2)
Press and hold down also "H" together with "I".
3)
Wait for nearly 3 seconds until the red led "M" flashes.
4)
Now the microprocessor is physically reset.
5)
Release both push-buttons "I" and "H"
6)
Press and hold down the "F" push-button to be programmed.
7)
After nearly 2 seconds the video-interphone emits a high-pitched
tone.
8)
Release the push-button "F" related to the self-start.
9)
On the entrance panels with push-buttons press the call push-but-
ton corresponding to the video -interphone; on the alphanumeric en-
trance panel, on the contrary, enter the call code and press "
10) A high-pitched tone will confirm the end of the procedure.
Restoring the default values of push-buttons
Programming phase:
1)
Press and hold down "I".
2)
Press and hold down also "H" together with "I".
3)
Wait for nearly 3 seconds until the red led "M" flashes.
4)
Now the microprocessor is physically reset.
5)
Release both push-buttons "I" and "H"
6)
Press and hold down the push-button to be restored to its default
setting.
7)
After 2 seconds the video-interphone emits a high-pitched tone.
8)
Release the push-buttons and press again the push-button to re-
store to its default setting.
Deleting all settings
This procedure is recommended when you want to change the ID of
a previously programmed video-interphone without retaining its pro-
gramming parameters.
Programming phase:
1)
Press and hold down "I".
2)
Then press and hold down also "H" together with "I".
3)
Wait for nearly 3 seconds until the red led "M" flashes.
4)
Now the microprocessor is physically reset.
5)
Release both push-buttons "H" and "I"
6)
Press and hold down the self-start push-button "H".
7)
After 2 seconds the video-interphone emits a continuous tone for
two seconds.
8)
Release the self-start push-button "H".
9)
During the long tone press the lock push-button "G".
If the deletion procedure was successful, press the lock push-but-
ton "G" and the video-interphone will emit a triple "BEEP".
P R O G R A M M I N G / O P E R A T I O N
OPERATION
Calls from an entrance panel, intercommunicating calls and landing calls
are differentiated by means of different tones.
Landing calls
Calls from entrance panels do not follow the pressing of the call push-
button but are generated internally by the video interphone. The call time
dwell or cycle consists of a ringtone of 1 second and a pause of 2 se-
conds, repeated twice (default setting of entrance panel). The duration of
"Ding-Dong" and "Ding-Dong-Dang" ringtones does not correspond to
the time dictated by the call cycle but to the natural duration of the rin-
gtone. To answer, press and release push-button "I". If push-button "I"
has already been pressed during the call, release it and press it again
The call answer time (30 s) and the conversation time (2 minutes by de-
fault) are set in the entrance panel parameters. Once the conversation
time has elapsed, conversation can be continued if the call is made again
within 10 s, from the same entrance panel.
During conversation, the audio can be interrupted momentarily (maxi-
mum 5 s) by pressing the "I" push-button.To resume conversation, press
the conversation push-button again within 5 s, otherwise communica-
tion is lost. Press push-button "I" to terminate the conversation. The red
LED "M" remains lit while the audio is active.
Intercommunicating call.
Press the intercommunicating push-button, if programmed, for the inter-
phone/video interphone to be called. The loudspeaker of the calling video
interphone will emit a ringing tone (if the call is possible) or an engaged
tone (if the call is not possible). On the called interphone/video interphone
the ringtone starts sequentially at intervals of 1 s ringing and 4 s pause.
The maximum duration of the call is 30 s (6 cycles). If you wish to inter-
rupt the call, press the conversation push-button "I" before an answer is
received from the called device. To answer a call, lift the handset on the
called interphone/video interphone, or press the conversation push-but-
ton. When answered, the video interphone enters direct communication
with the called device. Maximum duration of conversation is 5 minutes.
When the conversation time has elapsed, the user can continue without
replacing the handset if a new call is made within 10 s. Calls from the
entrance panel have priority over intercommunicating calls.
Denied calls.
The chime exclusion is indicated by the permanent lighting of the red
LED "M". If calls are made from the entrance panel to the video inter-
phone when the call mute is enabled, they are denied. A denied call cau-
ses the red LED "M" to briefly switch off according to the number of times
calls are denied (maximum 4 denied calls). The signal is repeated every
10 s (approx.). Deletion of denied calls is by re-enabling the ringtone, re-
setting the video interphone or a system power failure. On the entrance
".
panel, a denied call is indicated by means of a dissuasion tone (a series
of "Beeps" at 100ms intervals with a pause of 100ms for a total of 5 s).
The message "Do not disturb" also appears on entrance panels with di-
splay. The programming of push-buttons "G" and "I" can be changed
through two different configurations ("HANDS FREE" or with the
speak/listen push-button PRESSED), using the programmer type 950C
connected to a push-button entrance panel and/or an alphanumeric en-
trance panel with software version V4 or bigger. See instructions for pro-
grammer type 950C and entrance panels or electronic units.
Lock Button
The lock button of each device works in the following manner.
- Device with handset at rest
which it has spoken or from which it has been called.
- Device with handset raised but not engaged in a conversation
call to switchboard if the Switchboard flag is YES. Otherwise it goes
back to the first case.
- Device with handset raised and engaged in an internal conversation
as in the first case.
- Device with handset raised and engaged in an external conversation
or called from entrance panel lock
spoken with or from which it has been called.
In practice a lock is always activated except when the handset is raised
and you immediately press the lock button. This can also be taken to the
standard case if the system has no porter switchboard and the Swit-
chboard flag is set on NO.
NOTE: In series 6600 the equivalent operation is to press for an instant
the "open voice" push-button and then the lock release. Also in this case
the switchboard is called.
9/32
lock to the last entrance panel with
to the entrance panel being
GB
Publicidad
