Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Drive Control Lever/Auger Clutch
Lock* (If Equipped)
The drive control lever is located on the right
handle. Squeeze the control lever against the
handle to engage the wheel drive. Release to
stop. See Figure 3-5.
Figure 3-5
*On select models, the drive control lever also
locks the auger control lever so that you can
operate the chute directional control without
interrupting the snow throwing process. If the
auger control lever is engaged simultaneously
with the drive control lever, the operator can
release the auger control lever (on the left
handle) and the augers will remain engaged.
Release both control levers to stop augers and
wheel drive.
NOTE: Always release drive control lever
before changing speeds on all units except the
800-series hydro. Failure to do so will result
in increased wear on your machine's drive
system.
Steering Trigger Controls
(If Equipped)
The left and right wheel steering trigger
controls are located on the underside of the
handles. Refer to Figure 3-6.
Figure 3-6
•
Squeeze the right trigger control to turn
right.
•
Squeeze the left trigger control to turn
left.
CAUTION
Operate the snow thrower in open areas until you are
familiar with these controls.
Overhead Chute Directional
Control (If Equipped)
The overhead chute directional control
is located at the rear of the snow thrower
towards the left side of the unit under the
handle panel. To change the direction in
which snow is thrown, rotate chute directional
control. See Figure 3-7.
Figure 3-7
2-Way Chute Directional Control
Joystick (If Equipped)
The 2-Way chute directional control joystick is
located on the left side of the dash panel.
•
To change direction in which snow is
thrown, squeeze button on joystick and
pivot joystick to right or to the left. See
Figure 3-8.
Figure 3-8
4-Way Chute Directional Control
Joystick (If Equipped)
The 4-Way chute directional control joystick is
located on the left side of the dash panel.
•
To change the direction in which snow
is thrown, squeeze the button on the
joystick and pivot the joystick to the
right or to the left. See Figure 3-9.
•
To change the angle/distance which
snow is thrown, pivot the joystick
forward or backward.
Figure 3-9
Electric Chute Directional
Control Joystick (If Equipped)
The electric chute directional control joystick
is located on the right side of the dash panel.
Refer to Figure 3-10.
•
To change the direction in which snow
is thrown, move the joystick to the right
or to the left.
•
To change the angle/distance which
snow is thrown, pivot the joystick
forward or backward.
ELECTRIC CHUTE
DIRECTIONAL CONTROL
CHUTE TILT DOW N
CHUTE
ROTATE
LEFT
CHUTE TILT UP
Figure 3-10
Manual Chute Directional
Control (Units with Electric Chute
Directional Control Joystick)
Follow this procedure to manually change the
chute direction on units equipped with an
electric chute directional control joystick and
manual chute directional control rod only. See
Figure 3-1.
1.
Remove cotter pin (a) from either of the
holes furthest from the chute assembly on
chute rotation assembly. See Figure 3-11.
(a)
Figure 3-11
2.
Push in chute control rod until the hole
in it lines up with the third hole in chute
rotation assembly. See Figure 3-11.
3.
Reinsert cotter pin (a) through this hole
and chute control rod as shown in
Figure 3-11.
S
3 — c
ección
ontroleS y funcionamiento
CHUTE
ROTATE
RIGHT
15
Publicidad
Tabla de contenido
