Electrical Connection; Illustrated Description; Operating Instructions; Placement And Testing - stayer TH610 Manual De Instrucciones

The supplied additional handle 7 must first be fitted. To do
this, the clamp must be opened by turning the handle until it
is wide enough for the additional handle to be slid over the
chuck 1 and on to the hammer drill.
After you have positioned the additional handle 7, turn it to
the most comfortable working position for you.
Now turn the handle in the opposite direction again until the
additional handle is secure.
The additional handle 7 is suitable for both lefthanded and
right-handed users.
Fitting and adjusting the depth stop (Fig. 4/Item 2)
The depth stop 2 is held in place by the additional handle 7
by clamping. The clamp can be released and tightened by
turning the handle. Release the clamp and fit the depth stop
2 in the recess provided for it in the additional handle.
Set the depth stop 2 to the same level as the drill bit.
Pull the depth stop back by the required drilling depth.
Turn the handle on the additional handle 7 until it is secure.
Now drill the hole until the depth stop 2 touches the
workpiece.
Fitting the drill bit (Fig. 5-6)
Always pull the power plug before making adjustments to
the equipment.
The quick-change drill chuck 1 is equipped with a locking
fastener:
To lock = press the sleeve (a) forwards
To unlock = press the sleeve (a) backwards
release depth stop as described in the previous section
and push it towards the additional handle. This provides
free access to the chuck 1.
This hammer drill is fitted with a keyless chuck 1.
Open the chuck 1. The drill bit opening must be large
enough to fit the drill bit into.
Select a suitable drill bit. Push the drill bit as far as possible
into the chuck opening.
Close the chuck 1. Check that the drill bit is secure in the
chuck 1.
Check at regular intervals that the drill bit or tool is secure
(pull the mains plug).

3.3 Electrical connection

Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified on
the nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
If the power cable for this equipment is damaged, it must be
replaced by the manufacturer or its aftersales service or
similarly trained personnel to avoid danger.

3.4 Illustrated description

1. Drill chuck
2. Drill depth stop
3. Drill/hammer drill selector switch
4. Locking button
5. ON/OFF switch
6. Clockwise/Counter-clockwise switch
7. Additional handle
8. Speed controller
9. Gear Selection, Mechanical
ENGLISH
10

4. Operating instructions

4.1 Placement and testing

6.1 ON/OFF switch (Fig. 7/Item 5)
First fit a suitable drill bit into the tool (see 5.3).
Connect the mains plug to a suitable socket.
Position the drill in the position you wish to drill.
To switch on:
Press the ON/OFF switch 5
Continuous operation:
Secure the ON/OFF switch 5 with the locking button 4.
To switch off:
Press the ON/OFF switch 5 briefly.
Adjusting the speed (Fig. 7/Item 5)
You can infinitely vary the speed whilst using thetool.
Select the speed by applying a greater or lesserpressure to
the ON/OFF switch 5.
Select the correct speed: The most suitablespeed depends
on the workpiece, the type of useand the drill bit used.
Low pressure on the ON/OFF switch 5: Lower speed
(suitable for: small screws and soft materials)
Greater pressure on the ON/OFF switch 5:
Higher speed (suitable for large/long screws and hard
materials)
Tip:
Start drilling holes at low speed. Then increase the speed in
stages.
Benefits:
The drill bit is easier to control when starting the hole and
will not slide away.
You avoid drilling messy holes (for example in tiles).
Preselecting the speed (Fig. 7/Item 6)
The speed setting ring 8 enables you to define the
maximum speed. The ON/OFF switch 5 can only be
pressed to the defined maximum speed setting.
Set the speed using the setting ring 8 on the ON/OFF switch
5.
Do not attempt to make this setting whilst the drill is in use.
Clockwise/Counter-clockwise switch (Fig. 7/Item 6)
Change switch position only when the drill is at a standstill!
Switch the direction of the hammer drill using the
clockwise/counter-clockwise switch (6):
Direction
Clockwise (forwards and drill)
Counter-clockwise (reverse)
Drill / hammer drill selector switch (Fig. 8/Item 3)
Change switch position only when the drill is at a
standstill!
Drill
Drill / hammer drill selector switch 3 in the drill position.
(Position A)
Use for: Wood, metal, plastic
Hammer drill
Drill / hammer drill selector switch 3 in the hammer
drill position. (Position B)
Use for: Concrete, rock, masonry
10
Switch position
R
L