Milwaukee M12 HAMMERVAC Manual Del Operador página 4

ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
To reduce the risk of injury, always remove the
battery pack before removing the dust box. Do
not use tool without dust box and HEPA filter
in place.
Installing/Removing the Dust Box
and HEPA Filter
To remove the dust box:
1. Turn OFF the tool.
2. Remove the battery pack.
3. Press the dust box latch down.
4. Pull the dust box away from the
HAMMERVAC™.
5. Empty dust from the dust box.
6. If necessary, pull the HEPA filter
away from the dust box and tap
clean. Do not clean with water
or compressed air. After about 1500 holes or loss
of suction, discard and replace HEPA filter (Cat.
No. 49-90-2306).
To install the dust box:
1. Slide the dust box into the body of the
HAMMERVAC™.
2. The dust box latch should snap into place.
NOTE: Do not operate the HAMMERVAC™ without
the dust box and HEPA filter in place. Dust box cannot
be installed without HEPA filter.
Keep filter clean. Efficiency of the
CAUTION
HAMMERVAC™ is largely depen-
dent on the filter. A dirty filter will reduce the air
flow and overall efficiency of the system. Do not
clean with water or compressed air. Remove from
dust box and tap clean.
Installing/Removing Nozzle Assembly
To install the nozzle assembly
supplied with the tool, or acces-
sory nozzles:
1. With the nozzle assembly
pointing straight up, line up
the lugs of the nozzle as-
sembly with the lugs on the
front of the HAMMERVAC™.
The unlock symbol
nozzle assembly will line up
with the mark on the top of the
HAMMERVAC™.
1
2
on the
2. Turn the nozzle assembly left
or right to lock into place. The
lock symbol on the nozzle
assembly will line up with the
m a r k o n t h e t o p o f t h e
HAMMERVAC™.
3. To remove, reverse the proce-
dure.
Installing/Removing Nozzle
Replace the nozzle:
• After drilling about 1500 holes,
• When the bit brush shows signs
of wear,
• When suction is reduced,
• When dust escapes through the
bit brush during use
To replace the nozzle (Cat. No.
49-90-2300), press in the release
button and pull out from the lower
nozzle assembly. Slide the new
nozzle into the lower nozzle assem-
bly until it snaps into place.
Attaching the HAMMERVAC™ to a Rotary
Hammer/Hammer Drill
The HAMMERVAC™ is provided with three clamping
collar assemblies and one side handle grip. Choose
the correct clamping collar assembly for the tool
being used (see Specifications). The side handle
grip should be unscrewed from one assembly to be
used on another.
1. Turn OFF, remove the battery pack from the
HAMMERVAC™, and disconnect power from
the tool.
2. Remove the tool side handle.
3. Partially screw side handle grip onto clamping
collar assembly.
4. S l i d e
HAMMERVAC™ side
handle clamping col-
lar assembly over the
chuck and onto the
neck of the tool. The
clamp lever must be
facing up (3).
5. Attach the side han-
dle clamping collar
assembly onto the
HAMMERVAC™, first
the upper jaw, then lower jaw.
6. Press down the clamp lever (3) to secure the
clamping collar assembly to the HAMMERVAC™.
7. Rotate the HAMMERVAC™ and side handle grip
to the desired position, and tighten securely.
Adjusting the Side Handle Position
1. Loosen the side handle clamping collar assembly
by unscrewing the side handle grip until the side
handle clamping collar assembly rotates freely.
2. Rotate the side handle grip to the desired position.
3. Tighten the side handle grip securely.
4
3
t h e
1
2