Radio Reception; Usb Playback; Nfc Function - Sony XSP-N1BT Manual De Instrucciones

Ocultar thumbs Ver también para XSP-N1BT:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

The smartphone connected via a USB cable does
not charge.
 Make sure that the cable is connected correctly.
 Set [CHARGE] to [CHARGE STD] (page 17).

Radio reception

Stations cannot be received.
The sound is hampered by noises.
 The connection is not correct.
 If your car has built-in radio antenna (aerial) in
the rear/side glass, connect an REM OUT lead
(blue/white striped) or accessory power supply
lead (red) to the power supply lead of a car's
antenna (aerial) booster.
 Check the connection of the car antenna
(aerial).
 If the auto antenna (aerial) will not extend,
check the connection of the power antenna
(aerial) control lead.
Preset tuning is not possible.
 The broadcast signal is too weak.
RDS
PTY displays [- - - - - - - -].
 The current station is not an RDS station.
 RDS data has not been received.
 The station does not specify the program type.
CD playback
The disc does not play back.
 Defective or dirty disc.
 The CD-R/CD-RW is not for audio use (page 20).
MP3/WMA files cannot be played back.
 The disc is incompatible with the MP3/WMA
format and version. For details on playable discs
and formats, visit the support site.
MP3/WMA files take longer to play back than
others.
 The following discs take a longer time to start
playback.
 A disc recorded with a complicated tree
structure.
 A disc recorded in Multi Session.
 A disc to which data can be added.
The sound skips.
 Defective or dirty disc.

USB playback

You cannot play back items via a USB hub.
 This unit cannot recognize USB devices via a USB
hub.
A USB device takes longer to play back.
 The USB device contains files with a complicated
tree structure.
The sound is intermittent.
 The sound may be intermittent at a high-bit-rate
of more than 320 kbps.
Pandora® connection is not possible.
 Shut down the Pandora® application on the
mobile device, and then launch it again.
Application name is mismatched with the actual
application in App Remote.
 Launch the application again from the "App
Remote" application.

NFC function

One touch connection (NFC) is not possible.
 If the smartphone does not respond to the
touching.
 Check that the NFC function of the smartphone
is turned on.
 Move the N-Mark part of the smartphone
closer to the N-Mark part on this unit.
 If the smartphone is in a case, remove it.
 NFC receiving sensitivity depends on the device.
If One touch connection with the smartphone
fails several times, make BLUETOOTH connection
manually.
BLUETOOTH function
The connecting device cannot detect this unit.
 Before the pairing is made, set this unit to pairing
standby mode.
 While connected to a BLUETOOTH device, this
unit cannot be detected from another device.
 Disconnect the current connection and search
for this unit from another device.
 When the device pairing is made, set the
BLUETOOTH signal output to on (page 8).
Connection is not possible.
 The connection is controlled from one side (this
unit or BLUETOOTH device), but not both.
 Connect to this unit from a BLUETOOTH device
or vice versa.
The name of the detected device does not
appear.
 Depending on the status of the other device, it
may not be possible to obtain the name.
No ringtone.
 Adjust the volume by pressing VOL +/- while
receiving a call.
 Depending on the connecting device, the
ringtone may not be sent properly.
 Set [RINGTONE] to [1] (page 19).
25
GB

Publicidad

Tabla de contenido

Solución de problemas

loading

Tabla de contenido