Mixtrax Settings; Connections/Installation - Pioneer DEH-S2000UI Manual De Instrucciones

Reproductor de cd con receptor rds
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 58

MIXTRAX settings

Menu Item
SHORT PLAYBCK
[1.0 MIN], [1.5 MIN], [2.0 MIN],
[2.5 MIN], [3.0 MIN], [OFF]
FLASH AREA
[KEY/DISPLAY], [KEY], [OFF]
FLASH PATTERN
[SOUND LEVEL 1] to [SOUND LEVEL
6]
[LOW PASS 1] to [LOW PASS 6]
[RANDOM1]
[RANDOM2]
[RANDOM3]
DISPLAY FX
[ON], [OFF]
CUT IN FX
[ON], [OFF]
Description
Select the length of the playback time.
Select the area for the illumination effect.
When [OFF] is selected, the colour set under
the ILLUMINATION settings (page 12) is used as
the display colour.
Change the illumination effect according to
the sound and bass level.
The flash pattern changes according to the
sound level.
The flash pattern changes according to the
bass level.
The flash pattern changes randomly according
to the sound level mode and low pass mode.
The flash pattern changes randomly according
to the sound level mode.
The flash pattern changes randomly according
to the low pass mode.
Set the MIXTRAX special effects on/off.
Turn the MIXTRAX sound effects on/off while
manually changing the tracks.

Connections/Installation

Connections
Important
• When installing this unit in a vehicle
without an ACC (accessory) position on
the ignition switch, failure to connect the
red cable to the terminal that detects
operation of the ignition key may result
in battery drain.
ACC position
No ACC position
• Use of this unit in conditions other than
the following could result in fire or
malfunction.
– Vehicles with a 12-volt battery and
negative grounding.
– When speaker output is used by 4
channels, use speakers over 50 W
(maximum input power) and between 4
Ω to 8 Ω (impedance value). Do not use
1 Ω to 3 Ω speakers for this unit.
– When rear speaker output is used by 2
Ω of subwoofer, use speakers over 70 W
(maximum input power).
* Please refer to connections for a
connection method.
• To prevent a short-circuit, overheating or
malfunction, be sure to follow the
directions below.
– Disconnect the negative terminal of the
battery before installation.
– Secure the wiring with cable clamps or
adhesive tape. Wrap adhesive tape
around wiring that comes into contact
with metal parts to protect the wiring.
– Place all cables away from moving parts,
such as the shift lever and seat rails.
– Place all cables away from hot places,
such as near the heater outlet.
– Do not connect the yellow cable to the
battery by passing it through the hole
to the engine compartment.
– Cover any disconnected cable
connectors with insulating tape.
– Do not shorten any cables.
– Never cut the insulation of the power
cable of this unit in order to share the
power with other devices. The current
capacity of the cable is limited.
– Use a fuse of the rating prescribed.
– Never wire the negative speaker cable
directly to ground.
– Never band together negative cables of
multiple speakers.
• When this unit is on, control signals are
sent through the blue/white cable.
Connect this cable to the system remote
control of an external power amp or the
vehicle's auto-antenna relay control
terminal (max. 300mA 12 V DC). If the
vehicle is equipped with a glass antenna,
connect it to the antenna booster power
supply terminal.
• Never connect the blue/white cable to
the power terminal of an external power
amp. Also, never connect it to the power
terminal of the auto antenna. Doing so
may result in battery drain or a
malfunction.
• The black cable is ground. Ground cables
for this unit and other equipment
(especially, high-current products such as
power amps) must be wired separately. If
they are not, an accidental detachment
may result in a fire or malfunction.
• The graphical symbol
placed on
the product means direct current.
En
13

Publicidad

Tabla de contenido
loading

Tabla de contenido