Publicidad
CLEANING AND
MAINTENANCE
Cleaning must only be carried out by adults.
PRODUCT MAINTENANCE: protect from the
weather: water, rain, or snow; prolonged and
continuous exposure to bright sunlight may
give rise to colour changes of various different
materials; store this product in a dry place.
CLEANING THE CHASSIS: periodically clean all
plastic parts with a damp cloth. Do not use
solvent or similar cleaning products; keep all
metal parts dry to prevent rusting; keep moving
parts clean (adjustment mechanisms, locking
mechanisms, wheels, ...) and free of dust and
sand and, if necessary, lubricate with light
machine oil.
SEAT:
INSTRUCTIONS
1 OPENING: Before opening the Seat, remove
(without using blades) any die-cut cardboard.
Open the seat from the ends, pulling until it
clicks.
2 ATTACHING THE SEAT ONTO THE CHASSIS: To
fasten the Seat, position it on the chassis (fig_a)
and press down with both hands until it clicks
(fig_b).
Ensure the Seat is properly attached.
3 The Seat can be attached onto the chassis in
"world-facing" (fig_a) or "mum-facing" position
(fig_b).
4 Always engage the brake on the chassis before
fastening and unfastening the seat.
5 REMOVING THE YPSI SEAT FROM THE CHASSIS:
To unfasten the Seat, press the levers near the
chassis attachments (fig_a) and lift the seat at
the same time (fig_b).
6 HOOD: to use the hood, stretch it until it clicks
(so it is completely open).
7 The hood comes with a mesh insert so that the
baby can be seen from any position. To use it,
open the zips (fig_a) and slide the hood's insert
backwards (fig_b). Alternatively, the hood can
be stretched further forwards (fig_c).
8 Sliding the hood's attachments on the uprights
(fig_a), you can vary its distance from the seat
(fig_b).
9 ADJUSTING THE LEG REST: To switch from
"sitting" to "lying" or vice versa, simply press
on the leg rest to obtain the configuration you
wish.
10 FRONT BAR: The front bar can be removed by
pushing the buttons on the sides (fig_a), or
it can be opened on one side pressing one
button only (fig_b).
11 BED POSITION: the seat can be adjusted in
three positions, from "sitting" to "lying", with an
intermediate position (fig_a). To switch from
one position to another, pull the lever shown in
the picture (fig_b).
12 5-POINT SAFETY HARNESS: to fasten, insert
the two buckles into the waist strap (with the
straps attached in the crotch strap) until you
hear a click (fig_a). To unfasten them, press
the button which is situated at the centre of
the seatbelt buckle and pull the waist strap
outwards (fig_b).
13 To tighten the waist strap, pull on both sides in
the direction of the arrow; to loosen it, do the
opposite.
14 The safety harness can be adjusted in 3
positions according to the child's height. You
must use the higher positions as the child
grows bigger.
15 Adjust the height, inserting the straps with
shoulder pads through the eyelet in the
backrest (fig_a) and pull them through the
desired eyelets (fig_b).
16 FOLDING THE SEAT ATTACHED ONTO THE
CHASSIS: the Seat can be folded attached on
the chassis only in world-facing position (fig_a).
To do this:
- the leg rest must be in "sitting" position,
- fold down the hood,
- pull the levers on the up-right (fig_b)
- fold Seat onto itself (fig_c).
17 WARNING: If Seat is in mum-facing position, it
must be unfastened before folding (fig_a). It
can take up less room when folded (fig_b) and
can be conveniently carried using the supplied
handle (fig_c).
18 OPENING THE CHASSIS WITH SEAT ATTACHED:
Press the side attachment fastener downwards,
grip the upper ends of the handle bar and
rotate them towards you until the chassis
opens completely (fig_a). Chassis open (fig_b).
A "click" sound means it has opened correctly
and corresponds to the attachment onto the
base. Next, open the Ypsi Seat from the ends,
pulling it until it clicks (fig_c).
19 FOLDING THE CHASSIS WITH SEAT ATTACHED:
put the front wheels in locked position (fig_a),
lower the handle bar to the lowest position
(fig_b). Rotate the safety lever to the left (fig_c)
and, at the same time, pull the frame's internal
handle bar towards you (fig_d).
Lift the handle bar until the frame is completely
folded (fig_e).
WARNING: If the seat is mum-facing it cannot
be folded attached onto the chassis. It must be
unfastened.
20 To fold correctly, check the side fastener
is engaged (fig_a). If it has not engaged
automatically, compress the frame slightly. The
folded stroller is free-standing (fig_b).
21 TRANSPORT: the stroller can be conveniently
carried (with the front wheels in locked
position) using the central handle.
22 REMOVING THE SOFT COVER: to remove the
hood cover, unfasten the 2 buttons near the
pivots (fig_a), then press the buttons on the
two attachments and remove the hood (fig_b).
Lastly, extract the two rigid supports (fig_c).
23 To remove the soft cover from the seat, undo
the straps on the side of frame.
24 Open the zip that attaches the sack to the
horizontal bar (fig_a) and open the zip along
the frame (fig_b), then remove the sack.
25 Remove the metal rod from the back of the leg
rest.
26 To remove the sack, remove the rigid panel
from the back until you can see the eyelets
through which the belt ends pass (fig_a); insert
those ends in the eyelets so that the belts
- 21 -
Publicidad
