Prior To Start/Safety Test; Operation; Adjusting Driver's Seat; Programme Selection - Kärcher KM 130/300 R LPG Manual Del Usuario

1 Protective cover
2 Gas hose with union joint
3 Gas withdrawal valve
 Close gas drawing valve by turning it in
clock-wise direction.
 Unscrew the gas hose (30-mm span-
ner).
 Screw the protective cap onto the con-
necting valve of the empty gas cylinder.
 Open the cliplock.
 Replace the gas cylinder.
Observe the installation position of the
gas cylinder. The connection / ring
opening must point downwards.
 Unscrew the protective cap from the
connecting valve of the gas cylinder.
 Close the bracket closure.
 Screw the gas hose to the connecting
valve of the gas cylinder (30-mm span-
ner).
 Close the safety bar, and secure it with
a bolt.

Prior to start/safety test

 Check engine oil level.
 Check the water cooler.
 Check roller brush.
 Check tyre pressure.
 Adjust driver's seat.
 Shake off dust filter.
Note: For description, see section on Care
and maintenance.

Operation

DANGER
Long hours of using the appliance can
cause circulation problems on account of
vibrations.
It is not possible to specify a generally valid
operation time, since this depends on sev-
eral factors:
– Proneness to blood circulation deficien-
cies (frequently cold extremities, tin-
gling, numbness).
– Low ambient temperature. Wear warm
clothes to protect the affected body
parts.
– A firm grip impedes blood circulation.
– Continuous operation is worse than an
operation interrupted by pauses.
In case of regular, long-term operation of
the device and in case of repeated occur-
rence of the symptoms (e.g. tingling, numb-
ness in certain body parts) please consult a
physician.

Adjusting driver's seat

 Pull seat adjustment lever outwards.
 Slide seat, release lever and lock in
place.
 Check that the seat is properly locked in
position by attempting to move it back-
wards and forwards.

Programme selection

1 Transport drive
Recommended engine speed, 1500
rpm
2 Sweeping with sweep roller
Select engine speed, 2550 rpm
3 Sweeping using roller brush and side
brushes
Select engine speed, 2550 rpm

Open the gas supply

 Open the gas drawing valve by turning
it in anti-clockwise direction.

Starting the machine

Note: The machine is equipped with a seat
contact switch If the driver's seat is vacat-
ed, the machine is switched off.
 Sit on the driver's seat.
 Bring the direction selector switch into
the middle position.
 Lock parking brake.
Start the engine
 Insert the ignition key into the ignition
switch.
 Turn the ignition key to position "II".
 If the machine starts, release the igni-
tion key.
Note: Never operate the starter motor for
longer than 10 seconds. Wait at least 10
seconds before operating the starter motor
again.

Drive the machine

 Select engine speed, 1500 rpm.
 Set programme selection switch to
"Transport drive". .
 Press brake pedal and keep it de-
pressed.
 Release parking brake.
7
-
EN
Drive forward
 Set the travel direction switch to "for-
ward".
 Press accelerator pedal down slowly.
Reverse drive
Danger
Risk of injury! While reversing, ensure that
there is nobody in the way, ask them to
move if somebody is around.
ATTENTION
Risk of damage! Only use the direction
switch when the machine is standing still.
 Set the travel direction switch to "back-
wards".
 Press accelerator pedal down slowly.
Driving method
– The accelerator pedal can be used to
vary the driving speed infinitely.
– Avoid pressing the pedal suddenly as
this may damage the hydraulic system.
– In the event of power loss on inclined
surfaces, slightly reduce the pressure
on the accelerator pedal.
Brakes
 Release the accelerator pedal, the ma-
chine brakes automatically and stops.
Note: The braking effect can be supported
by pressing the brake pedal.
Driving over obstacles
Driving over fixed obstacles which are
70 mm (2.75 inch) high or less:
 Drive forwards slowly and carefully.
Driving over fixed obstacles which are
more than 70 mm (2.75 inch) high:
 Only drive over these obstacles using a
suitable ramp.

Sweeping mode

ATTENTION
Do not sweep up packing strips, wire or
similar objects as this may damage the
sweeping mechanism.
 For sweeping operation, set the engine
speed to 2550 rpm, see chapter "Multi-
function display | Setting the rpm".
Note
Settings of 1500 rpm are only intended
for transport travel and not for sweeping
operation (sweeping brush and side
brushes do not turn sufficiently).
Note: To achieve an optimum cleaning re-
sult, the driving speed should be adjusted
to take specific situations into account.
Note: During operation, the dust filter
should be shaken off and cleaned at regu-
lar intervals.
Upgrade kit water spray system (option)
This upgrade kit is factory-installed and
cannot be installed retroactively.
The water spray system upgrade kit con-
sists of a water tank and the spray nozzles
on the side brushes.
 If a lot of dust is generated during
sweeping, the water spraying system
can be used.
 The switching is done via the irrigation
switch for the side brush.
9