Rethermalization
1. Press the ON/OFF button to turn on the equipment.
2. Fill the included Vollrath induction ready inset with cooked, chilled
food. Place the inset into the equipment. Close the lid. For best
results keep the lid closed while heating and serving.
3. Press the function button to select the Retherm (Rethermalize)
mode.
4. While the food is rethermalizing, the retherm light will illuminate and
the display will show the target temperature of 74 ºC.
5. The stir light may blink to indicate the food should be stirred for
even heating. For best results stir the food often, approximately
every 15 minutes.
6. Monitor the food temperature closely for food safety. The United
States Public Health Service recommends that hot food be held at a
minimum of 140 ºF (60 ºC) to help prevent bacteria growth.
Note: This equipment monitors the temperature of the inset and
automatically adjusts the output to maintain the user
controlled set point. Temperatures displayed may vary
from actual food temperatures depending on the type of
food and stirring frequency. For best results adjust the
settings as needed to achieve the desired temperature of
each menu item. Some foods may require a higher setting
to hold at the desired temperature.
7. The display will blink if the inset is removed.
8. After the inset has reached approximately 74 ºC, the equipment will
switch to hot food holding mode. The warm light will illuminate and
the display will show the default setting for Hot Food Holding.
9. Follow the instructions for Hold Hot Food at Serving Temperature.
Do not add cold food to rethermalized hot food.
Hot Food Holding
Select a temperature at which to hold hot food.
Preheat the Warmer
1. Press the ON/OFF button to turn on the equipment.
2. Place the empty Vollrath induction ready inset into the equipment.
3. Press the up arrow to select a temperature above 68 ºC.
4. Allow the equipment to heat for 5 minutes.
Hold Hot Food at Serving Temperature
1. Fill the included Vollrath induction ready inset with pre-heated food,
above 68 ºC. Place the inset into the drop-in. For best results keep
the lid closed while heating and serving.
2. Select a holding temperature. Press the function button to select
Warming.
3. The warming light blinks until the inset heats to the set temperature.
4. The stir light may blink to indicate the food should be stirred for
even heating. For best results stir the food often, approximately
every 15 minutes.
5. Monitor the food temperature closely for food safety. The United
States Public Health Service recommends that hot food be held at a
minimum of 140 ºF (60 ºC) to help prevent bacteria growth.
Note: This equipment monitors the temperature of the inset and
automatically adjusts the output to maintain the user
controlled set point. Temperatures displayed may vary
from actual food temperatures depending on the type of
food and stirring frequency. For best results adjust the
settings as needed to achieve the desired temperature of
each menu item. Some foods may require a higher setting
to hold at the desired temperature.
6. The display will blink if the inset is removed.
®
Mirage
Countertop Induction Rethermalizers Operator's Manual
Lock the Control Panel (optional)
Lock
At the same time, press and hold the function button and the arrow
down button until the lock light appears.
Unlock
At the same time, press and hold the function button and the arrow
down button until the unlock light appears.
CLEANING
WARNING
Electrical Shock Hazard
Keep water and other liquids from entering the inside of the
equipment. Liquid inside the equipment could cause an
electrical shock. Do not spray water or cleaning products.
Liquid could contact the electrical components and cause a
short circuit or an electrical shock.
CAUTION
Burn Hazard
Hot surfaces and food can burn skin. Allow the hot surfaces to
cool before handling. Do not drop or spill water onto the
cooking surface as it can spray or splatter.
To maintain the appearance and increase the service life, clean this
equipment daily.
What you will need:
• Three soft clean cloths, one each for cleaning, rinsing and drying
• Mild dish washing detergent
• Clean warm water
NOTICE: Failure to follow these cleaning instructions may lead to
product damage that will not be covered under warranty.
1. Unplug the equipment and let it completely cool.
2. Use a soft cloth moistened with warm water and a mild dish washing
detergent to clean the well and the rim.
NOTICE: Do NOT use cleaning solutions that contain chlorine or
bleach ingredients. Use of solutions with these
ingredients will damage the well and will void the
.
warranty
3. Use the second clean soft clean soft cloth moistened with clean
warm water to wipe all detergent from the well and the rim.
4. Use the third soft clean cloth to dry the well and the rim.
NOTICE: Failure to throughly remove all detergent or thoroughly
dry the equipment may result in damage to the
equipment.
5. The stainless steel insert is dishwasher safe.
3