Kettler EX 1 Instrucciones De Montaje página 4

■ If the equipment is in regular use, check all its components thor-
oughly every 1 -2 months. Pay particular attention to the tightness
of bolts and nuts.This applies especially to the securing bolts for
saddle and handelbars.
■ To ensure that the safety level is kept to the highest possible
standard, determined by its construction, this product should be
serviced regulary (once a year) by specialist retailers.
■ Instruct persons using the equipment (in particular children) on
possible sources of danger during exercising.
■ The unit requires a power supply of 220-230 V/50 Hz. It should
be connected only to a safety socket with a single 10-A fuse. Before
commissioning the appliance pay attention to the fact that the
correct plug-in power supply unit (observe marking) has been con-
nected properly.
■ Important: Do not under any circumstances carry out electrical
repairs or alterations yourself. Always ensure that such work is
done by a properly qualified electrician.
■ mportant: disconnect the apparatus from the mains before doing
repair, maintenance or cleaning work.
■ Do not use a multiple power socket for the running belt. If an
extension cable is being used, ensure that it complies with the
VDE regulations.
■ When the unit is not in use, unplug it from the power supply.
■ Ensure that the power cable is not pinched and that no-one can
trip over it.
Handling the equipment
■ Before using the equipment for exercise, check carefully to
ensure that it has been correctly assembled.
■ It is not recommended to use or store the apparatus in a damp
room as this may cause it to rust. Please ensure that no part of
the machine comes in contact with liquids (drinks, perspiration etc.).
This may cause corrosion.
■ The machine is designed for use by adults and children should
not be allowed to play with it. Children at play behave unpre-
dictably and dangerous situations may occur for which the
manufacturer cannot be held liable. If, in spite of this, children
are allowed to use the equipment, ensure that they are instructed
in its proper use and supervised accordingly.
■ The exercise cycle complies with the DIN EN 957 - 1/5, class
HA. It is therefore suitable for therapeutic use.
■ Before beginning your first training session, familiarize yourself
thoroughly with all the functions and settings of the unit.
Instructions for Assembly
■ Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
■ Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the diagrams.
The correct sequence is given in capital letters.
■ The equipment must be assembled with due care by an adult
person. If in doubt call upon the help of a second person, if pos-
sible technically talented.
■ Please note that there is always a danger of injury when working
with tools or doing manual work. Therefore please be careful
when assembling this machine.
■ Ensure that your working area is free of possible sources of danger, for
example don't leave any tools lying around. Always dispose pack-
aging material in such a way that it may not cause any danger. There
is always a risk of suffocation if children play with plastic bags!
4
■ All electric appliances emit electromagnetic radiation when in oper-
ation. Please do not leave especially radiation-intensive appliances
(e.g. mobile telephones) directly next to the cockpit or the elec-
tronic controlsystem as otherwise values displayed might be dis-
torted (e.g. pulse measurement).
■ Before beginning your program of exercise, consult your doctor
to ensure that you are fit enough to use the equipment. Base your
program of exercise on the advice given by your doctor. Incorrect
or excessive exercise may damage your health!
■ Any interference with parts of the product that are not described
within the manual may cause damage, or endanger the person
using this machine. Extensive repairs must only be carried out
by KETTLER service staff or qualified personnel trained by KETTLER.
■ Always observe the general safety rules and precautions for
working with electrical equipment.
■ Before beginning your program of training, study the instructions
for training carefully.
■ Our products are subject to a constant innovative quality assurance.
We reserve the right to perform technical modifications.
■ In case of enquiry, please contact your KETTLER dealer.
■ In choosing the location of the apparatus, ensure a sufficient safety
distance from any obstacles. The apparatus must not be mounted
in the immediate vicinity of main passageways (paths, doorways,
corridors).
■ For a comfortable training position please adjust the handlebar and-
saddle position to your body height.
■ A slight production of noise at the bearing of the centrifugal mass
is due to the construction and has no negative effect upon ope-
ration. Possibly occurring noise during reverse pedalling result
from engineering and are absolutely safe.
■ The exercise cycle has a magnetic brake system.
■ The equipment is independent of revolutions per minute.
■ Please ensure that liquids or perspiration never enter the machine
or the electronics.
■ Before use, always check all screws and plug-in connections as
well as respective safety devices fit correctly.
■ Always wear suitable shoes when using.
■ Do not use corrosive or abrasive materials to clean the equipment.
Ensure that such materials are not allowed to pollute the envi-
ronment.
■ The product is not suitable for use by persons weighing over 110
kg.
■ The fastening material required for each assembly step is shown
in the diagram inset. Use the fastening material exactly as
instructed. The required tools are supplied with the equipment.
■ Bolt all the parts together loosely at first, and check that they have
been assembled correctly. Tighten the locknuts by hand until resi-
stance is felt, then use spanner to finally tighten nuts completely
against resistance (locking device). Then check that all screw
connections have been tightened firmly. Attention: once locknuts
have been unscrewed they no longer function correctly (the
locking device is destroyed), and must be replaced.
■ To pull off the pedal arms remove cap and screw (A). Grip the pedal
arm tightly, and screw in an M12 bolt (not supplied) into the thread
(B). After a few turns you may take off the pedal arm (C).
■ For technical reasons, we reserve the right to carry out preliminary
assembly work (e.g. addition of tubing plugs).
■ Please keep original packaging of this article, so that it may be used
for transport at a later date, if necessary.