Mounting The Base Unit On A Wall; Troubleshooting - Sony SPP-SS951 Manual De Instrucciones

To store a number to be dialed via Private Branch Exchange (PBX)
Before entering a phone number in Step 4, do as follows:
1
Enter the outside line access digit (e.g., 9).
2
Press (REDIAL/PAUSE).
To change a stored number
Store a new number, as described previously.
Making calls with speed dialing
1
Press (TALK) and wait until the TALK/BATT LOW lamp lights up.
2
Press (SPEED DIAL).
3
Enter the desired speed dialing number ((0) to (9)).
The phone number stored in the speed dialing number will be dialed.
Paging
You can page the handset from the base unit. Note that you can't page if the
handset is in use.
Note
You can't page the handset when its RING switch is set to OFF.

Mounting the base unit on a wall

1
Reverse the hang-up tab.
2
Plug the telephone line cord to the LINE jack and the AC power
adaptor to the DC IN 9V jack, and hook the cords. Use the shorter
cord for mounting.
3
Attach the wall bracket to the center of the base unit. Align the ¢
marks of the wall bracket with those of the base unit.
4
Plug the telephone line cord to the telephone outlet, and hook the
base unit to the wall plate.
5
Plug the AC power adaptor to an AC outlet. Then raise the antenna so
that it points towards the ceiling.
1 2
Telephone
line cord
AC power
Wall
adaptor
bracket
cord
Tip
To remove the wall bracket, press the lower tabs.
Maintenance
• Clean the cabinets with a soft cloth slightly moistened with water or a mild
detergent solution. Do not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine as they may damage the finish of the
cabinet.
• If the charge terminals of the base unit and handset are soiled, wipe them with
a soft cloth or paper.
If you have any questions or problems concerning your phone, please consult
your nearest Sony dealer.
To page
Press (HANDSET LOCATOR).
The handset rings.
When you keep pressing
(HANDSET LOCATOR), the handset
rings continuously.
3 4,5
Wall plate
1
2
AC power
adaptor
AC outlet
Notes on power sources
On battery pack
• Store the battery pack at a temperature between 41°F (5°C) and 95°F (35°C) for
best performance.
• If you do not use the cordless handset for a long period of time, remove the
battery pack, after charging for more than 12 hours.
On power failure
• During a power interruption, you cannot make or receive calls.
For the customers in the USA
RECYCLING NICKEL-CADMIUM BATTERIES
NICKEL-CADMIUM BATTERY.
BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
Nickel-Cadmium batteries are recyclable. You can help preserve our
environment by returning your unwanted batteries to your nearest Sony
Service Center for collection, recycling or proper disposal.
Note: In some areas the disposal of nickel-cadmium batteries in household
or business trash may be prohibited.
For the Sony Service Center nearest you call 1-800-222-SONY (United States only)
Caution: Do not handle damaged or leaking nickel-cadmium batteries.

Troubleshooting

Remedy
Symptom
You cannot make or receive • Place the base unit away from noise sources.
• Move the handset closer to the base unit.
calls.
You hear no dial tone. • Make sure you set up the base unit correctly.
• Make sure the battery is fully charged.
• Make sure the dialing mode setting (pulse or tone) is
The phone does not connect at
correct.
all, even the number you dial is
correct.
• Make sure the last dialed number is really the one you
The phone doesn't redial
want to dial.
correctly.
• The number you last dialed exceeds 32 digits
You hear five short error beeps
(including the tone and pause digits if used).
when you try to redial.
• The number you last dialed is erased.
• Make sure the number (including the tone and pause
You cannot store a speed dial
digits) does not exceed 16 digits.
number.
• Set the RING switch to ON.
The handset does not ring.
• Move the handset closer to the base unit.
You hear interference during
• Place the base unit away from noise sources.
conversation.
• It is an out-of-range alarm. Move the handset closer to
You hear a beep every second
the base unit within one minute.
during conversation.
• The battery is weak. Charge the battery for more than
You hear a beep every three
12 hours.
seconds and the TALK/BATT
LOW lamp flashes.
Specifications
General
Spread method Direct-Sequence Spread-Spectrum
Access method FDMA-TDD
Frequency band 902 – 928 MHz
Operation channel 20 channels
Supplied accessories AC power adaptor (1)
Telephone line cords (2)
Rechargeable battery pack BP-T24 (1)
Directories (2 sheets)
Wall bracket/stand (1)
Handset
Power source Rechargeable battery pack BP-T24
Battery life Standby: Approx. 10 days (RING ON mode)
Approx. 1 month (RING OFF mode)
Talk: Approx. 6 hours
Dimensions Approx. 58 x 177 x 46 mm (w/h/d), antenna excluded
3
(Approx. 2 ⁄
8
Antenna: 72 mm (2
Mass Approx. 250 g (Approx. 8.8 oz), battery included
Base unit
Power source DC 9V from AC power adaptor
Battery charging time Approx. 12 hours
Dimensions Approx. 128 x 58 x 208 mm (w/h/d), antenna excluded
1
(Approx. 5 ⁄
8
Antenna: 165 mm (6
Mass Approx. 320 g (Approx. 11 oz), wall bracket excluded
Design and specifications are subject to change without notice.
13
x 7 x 1 ⁄ inches)
16
7 ⁄ inches)
8
3 1
x 2 ⁄ x 8 ⁄ inches)
8 4
1 ⁄ inches)
2