Mounting The Base Unit On A Wall; Troubleshooting - Sony SPP-SS950 Manual De Instrucciones

To store a number to be dialed via Private Branch Exchange (PBX)
Before entering a phone number in Step 4, do as follows:
1
Enter the outside line access digit (e.g., 9).
2
Press (REDIAL/PAUSE).
To change a stored number
Store a new number, as described previously.
Making calls with speed dialing
1
Press (TALK) and wait until the TALK/BATT LOW lamp lights up.
2
Press (SPEED DIAL).
3
Enter the desired speed dialing number ((0) to (9)).
The phone number stored in the speed dialing number will be dialed.
Paging
You can page the handset from the base unit. Note that you can't page if the
handset is in use.
Note
You can't page the handset when its RING ON/BATT SAVE is set to BATT SAVE.

Mounting the base unit on a wall

1
Reverse the hang-up tab.
2
Plug the telephone line cord to the LINE jack and the AC power
adaptor to the DC IN 9V jack, and hook the cords. Use the shorter
cord for mounting.
3
Attach the wall bracket to the center of the base unit. Align the ¢
marks of the wall bracket with those of the base unit.
4
Plug the telephone line cord to the telephone outlet, and hook the
base unit to the wall plate.
5
Plug the AC power adaptor to an AC outlet. Then raise the antenna so
that it points towards the ceiling.
1 2
Telephone
line cord
AC power
Wall
adaptor
bracket
cord
Tip
To remove the wall bracket, press the lower tabs.
Maintenance
• Clean the cabinets with a soft cloth slightly moistened with water or a mild
detergent solution. Do not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine as they may damage the finish of the
cabinet.
• If the charge terminals of the base unit and handset are soiled, wipe them with
a soft cloth or paper.
If you have any questions or problems concerning your phone, please consult
your nearest Sony dealer.
To page
Press (PAGE).
The handset rings.
When you keep pressing (PAGE),
the handset rings continuously.
3 4,5
Wall plate
1
2
AC power
adaptor
AC outlet
Notes on power sources
On battery pack
• Store the battery pack at a temperature between 41°F (5°C) and 95°F (35°C) for
best performance.
• If you do not use the cordless handset for a long period of time, remove the
battery pack, after charging for more than 12 hours.
On power failure
• During a power interruption, you cannot make or receive calls.
RECYCLING NICKEL-CADMIUM BATTERIES
NICKEL-CADMIUM BATTERY.
BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
Nickel-Cadmium batteries are recyclable. You can help preserve our
environment by returning your unwanted batteries to your nearest Sony
Service Center for collection, recycling or proper disposal.
Note: In some areas the disposal of nickel-cadmium batteries in household
or business trash may be prohibited.
For the Sony Service Center nearest you call 1-800-222-SONY (United States only)
Caution: Do not handle damaged or leaking nickel-cadmium batteries.

Troubleshooting

Symptom Remedy
You cannot make or receive
• Place the base unit away from noise sources.
calls.
• Move the handset closer to the base unit.
You hear no dial tone.
• Make sure you set up the base unit correctly.
• Make sure the battery is fully charged.
The phone does not connect at
• Make sure the dialing mode setting (pulse or tone) is
all, even the number you dial is
correct.
correct.
The phone doesn't redial
• Make sure the last dialed number is really the one you
correctly.
want to dial.
You hear five short error beeps
• The number you last dialed exceeds 32 digits
when you try to redial.
(including the tone and pause digits if used).
• The number you last dialed is erased.
You cannot store a speed dial • Make sure the number (including the tone and pause
number. digits) does not exceed 16 digits.
The handset does not ring. • Set the RING ON/BATT SAVE switch to RING ON.
You hear interference during • Move the handset closer to the base unit.
• Place the base unit away from noise sources.
conversation.
• It is an out-of-range alarm. Move the handset closer to
You hear a beep every second
during conversation. the base unit within one minute.
• The battery is weak. Charge the battery for more than
You hear a beep every three
12 hours.
seconds and the TALK/BATT
LOW lamp flashes.
Specifications
General
Spread method Direct-Sequence Spread-Spectrum
Access method FDMA-TDD
Frequency band 902 – 928 MHz
Operation channel 20 channels
Supplied accessories AC power adaptor AC-T37 (1)
Telephone line cords (2)
Rechargeable battery pack BP-T18 (1)
Directories (2 sheets)
Wall bracket/stand (1)
Handset
Power source Rechargeable battery pack BP-T18
Battery life Standby: Approx. 7 days (RING ON mode)
Approx. 3 weeks (BATT SAVE mode)
Talk: Approx. 4 hours
Dimensions Approx. 58 x 177 x 46 mm (w/h/d), antenna excluded
(Approx. 2 3 ⁄
8
Antenna: 72 mm (2
Mass Approx. Approx. 250 g (Approx. 8.8 oz), battery included
Base unit
Power source DC 9V from AC power adaptor
Battery charging time Approx. 12 hours
Dimensions Approx. 128 x 58 x 208 mm (w/h/d), antenna excluded
(Approx. 5 1 ⁄
8
Antenna: 165 mm (6
Mass Approx. 320 g (Approx. 11 oz), wall bracket excluded
Design and specifications are subject to change without notice.
x 7 x 1 13 ⁄ inches)
16
7
⁄ inches)
8
x 2 3 ⁄ x 8 1 ⁄ inches)
8 4
1
⁄ inches)
2