Husqvarna GT48XLSi Manual De Operario página 13

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL
The engine in your tractor has been shipped from the fac-
tory already filled with sum mer weight oil.
Check engine oil with tractor on level ground.
Remove oil fill cap/dipstick and wipe clean, reinsert the
dipstick and screw cap tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
"FULL " mark on dipstick is reached. Do not overfill.
For cold weather operation you should change oil for
easier starting. (See "OIL VISCOSITY CHART" in the
Maintenance sec tion of this manual.)
To change engine oil, see the Maintenance section in
this manual.
ADD GASOLINE
Fill fuel tank to bottom of filler neck. Do not overfill.
Use fresh, clean, regular gasoline with a minimum of
87 octane. Do not mix oil with gasoline. Purchase fuel
in quantities that can be used within 30 days to ensure
fuel freshness.
CAUTION: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
IMPORTANT: WHEN OPERATING IN TEMPERATURES
BELOW 32°F (0°C), USE FRESH, CLEAN WINTER GRADE
GASOLINE TO HELP ENSURE GOOD COLD WEATHER
STARTING.
CAUTION: Alcohol blended fuels (called gasohol
or using ethanol or methanol) can attract moisture
which leads to sep a ra tion and for ma tion of acids
during storage. Acidic gas can damage the fuel
system of an engine while in storage. To avoid
engine problems, the fuel system should be emptied
before stor age of 30 days or longer. Drain the gas
tank, start the engine and let it run until the fuel
lines and carburetor are empty. Use fresh fuel next
season. See Storage In struc tions for additional
information. Never use engine or carburetor cleaner
products in the fuel tank or permanent damage may
occur. Fuel stabilizer is an acceptable alternative
in minimizing the formation of fuel gum deposits
during stor age. Add stabilizer to gasoline in fuel
tank or storage container. Always follow the mix
ratio found on stabilizer container. Run engine at
least 10 minutes after adding stabilizer to allow the
stabilizer to reach the carburetor. Do not empty
the gas tank and carburetor if using fuel stabilizer.
OPERATION
RESERVE FUEL VALVE OPERATION
(See Fig. 17)
1. Raise seat to access reserve fuel valve.
2. In normal operation, valve should be set to primary (as
shown in view)
3. If tractor runs out of fuel, rotate valve handle to reserve.
4. Drive tractor to be refueled.
5. After refueling, return valve to primary position.
RESETTING IGNITION SYSTEM PASSCODE
(See Fig. 18)
The SmartSwitch Ignition is preset at the factory with the
default code "321". To reset or change the passcode, the
operator does not have to be seated on the tractor.
1. Press the SmartSwitch Ignition (SSI) button (F) once (or
sit on the seat). Ensure the indicator is blinking blue.
2. Press and hold the (1) and (3) buttons simultaneously
for approximately three (3) seconds until the SSI button
changes to solid blue.
3. Using the numbered buttons, enter the desired pass-
code. The passcode may be anywhere from one to
five digits in length.
4. After the desired passcode has been entered, press
the SSI button (F) once.
NOTE: When the indicator flashes green, the passcode has
been accepted. If the indicator blinks red, the passcode has
not been accepted. Wait until the indicator returns to blink-
ing blue and repeat this procedure starting from step two.
13
RESERVE
RESERVE
FUEL VALVE
FUEL VALVE
PRIMARY
PRIMARY
Fig. 17
F
Fig. 18
RESERVE
RESERVE

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido