Troubleshooting - Husqvarna GT48XLSi Manual De Operario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

PROBLEM
CAUSE
1. Out of fuel.
Will not start
2. Engine flooded.
3. Bad spark plug.
4. Dirty air filter.
5. Dirty fuel filter.
6. Water in fuel.
7. Loose or damaged wiring.
8. Engine valves out of adjustment.
1. Dirty air filter.
Hard to start
2. Bad spark plug.
3. Weak or dead battery.
4. Dirty fuel filter.
5. Stale or dirty fuel.
6. Loose or damaged wiring.
7. Engine valves out of adjustment.
1. Brake pedal not depressed.
Engine will not
2. Attachment clutch is engaged.
turn over
3. Weak or dead battery.
4. Blown fuse.
5. Corroded battery terminals.
6. Loose or damaged wiring.
7. Faulty ignition switch.
8. Faulty solenoid or starter.
9. Faulty operator presence switch(es).
1. Weak or dead battery.
Engine clicks but
2. Corroded battery terminals.
will not start
3. Loose or damaged wiring.
4. Faulty solenoid or starter.
1. Cutting too much grass/too fast.
Loss of power
2. Throttle in cold weather starting position (
3. Build-up of grass, leaves, trash under mower.
4. Dirty air filter.
5. Low oil level/dirty oil.
6. Faulty spark plug.
7. Dirty fuel filter.
8. Stale or dirty fuel.
9. Water in fuel.
10. Spark plug wire loose.
11. Dirty engine air screen/fins.
12. Dirty/clogged muffler.
13. Loose or damaged wiring.
14. Engine valves out of adjustment.
1. Worn, bent or loose blade.
Excessive
2. Bent blade mandrel.
vibration
3. Loose/damaged part(s).

TROUBLESHOOTING

29
CORRECTION
1. Fill fuel tank.
2. Wait several minutes before attempting to start.
3. Replace spark plug.
4. Clean/replace air filter.
5. Replace fuel filter.
6. Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
7. Check all wiring.
8. Contact an authorized service center/department.
1. Clean/replace air filter.
2. Replace spark plug.
3. Recharge or replace battery.
4. Replace fuel filter.
5. Empty fuel tank and refill tank with fresh, clean gas.
6. Check all wiring.
7. Contact an authorized service center/department.
1. Depress brake pedal.
2. Disengage attachment clutch.
3. Recharge or replace battery.
4. Replace fuse.
5. Clean battery terminals.
6. Check all wiring.
7. Check/replace ignition switch.
8. Check/replace solenoid or starter.
9. Contact an authorized service center/department.
1. Recharge or replace battery.
2. Clean battery terminals.
3. Check all wiring.
4. Check/replace solenoid or starter.
1. Raise cutting height/reduce speed.
).
2. Move throttle control to fast position (
3. Clean underside of mower housing.
4. Clean/replace air filter.
5. Check oil level/change oil.
6. Clean and regap or change spark plug.
7. Replace fuel filter.
8. Empty fuel tank and refill tank with fresh, clean gas.
9. Empty fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter.
10. Connect and tighten spark plug wire.
11. Clean engine air screen/fins.
12. Clean/replace muffler.
13. Check all wiring.
14. Contact an authorized service center/department.
1. Replace blade. Tighten blade bolt.
2. Replace blade mandrel.
3. Tighten loose part(s). Replace damaged parts.
).

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido